Astralpool 35450 Manual De Instalación Y Mantenimiento página 2

ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be implemented
for installation and start-up. Therefore, the installer as well as the user must read the instructions before beginning installation
and start-up.
Keep this manual for future reference.
To achieve optimum performance of the Underwater projector for led fountains, follow the instructions indicated below:
1. VERIFY THE CONTENTS OF THE PACKING:
The following accessories are included inside the box:
•
Projector unit
•
Projector holder unit
•
Bag of fastenings
•
Installation and maintenance manual
2. GENERAL CHARACTERISTICS:
This floodlamp has been designed to be used fully submerged underwater in fresh water swimming pools. It is a Class III electric
apparatus with very low safety voltage (12 V with alternating current).
The floodlamp complies with IPX8 degree of protection (resistance to penetration of dust, solid bodies and humidity) at a nominal
Immersion depth of 2 m.
This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard. LIGHTS PART 2:
SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The mains supply to the light should have 30 mA overload protection. The power supply transformer of these projectors must be an
insulated safety transformer with separate spooling.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric components which
have been inserted or handled at locations other than its own premises.
3. INSTALLATION:
• In order to clearly light a pool It Is recommended lo Install a floodlamp every 20 m² of water surface. In swimming pools which are
especially deep, a floodlamp ¡s required for every 25 m² of water volume.
• In order to prevent glare, the floodlamps should be installed so that they face away from the residence or usual view of the
swimming pool.
• To avoid the need to empty the pool to change the lamp, we recommend that the floodlamp be installed in areas which are
accessible from the upper edge of the pool.
• In installations where you want to replace a conventional spotlight by a LED projector, using the existing wiring, it is strongly
recommended to use underwater resin splicing. It is not recommended to use silicone to try to seal the connection point of the
wires. The spotlight should not be handled under any circumstances as this would lead to losing the guarantee.
Prior to installation verify that the gland seal (no. 11) has been fully tightened.
Follow these steps for installation:
1. Make 3 holes in the bottom of the fountain (Fig. 1)
2. Place the base of the holder and fasten the three screws (Fig. 2)
3. Place the Projector on the holder and adjust the projection inclination with screws 8 and 16 (Fig.3).
4. MAINTENANCE:
This projector does not require any type of maintenance. If the projector does not work properly, please contact our customer
attention department.
It is forbidden to handle the inside of the projector. All projectors which have been handled will lose their guarantee.
If you wish to remove the projector from the swimming pool, it must be done by suitably qualified technician.
To remove the floodlamp to the edge of the swimming pool loosen the tree DIN 7983 4,8x38 screws (Nº 21) until the fastening dog
lelds sufficiently so that the floodlamp unlí can be separated from the housing.
Attention:
• Before any handling ensure that there is NO voltage supplied to the floodlamp.
The Projector 35451 does not need any control because it emits only white light.
The Projector 35450 needs control for the change of color and for the change of sequences.
5. CONTROL SYSTEMS OF THE LED PROJECTORS:
The LED projectors can be controlled in two different ways: either by a normally closed pushbutton or by means of the modulator
receiver and/or remote control
In both cases, you should make sure that the voltage received by the lamp is never more than 12V.
The projector should only be operated underwater and anchored to the vertical walls of the pool. The spotlight is supplied with heat
protection, which in the event of excess temperature reduces the lighting level to avoid overheating.
A T T E N T I O N
2