Programming Pre-Set Buttons - Vitamix The Quiet One 036019-ABAB Manual De Instrucciones

c
Speed Control Pre-Set Programs
On/Off Power Switch: Located on the back of the motor base, the On/Off switch
controls the power to the machine. While plugged in, switch to on to ready the
machine for blending. Shut off the power switch at night or whenever the machine
will be left unattended.
Start /Stop Button: Pressing Start( )/Stop( ) once starts and runs the machine and
turns the blade. Press Start/Stop button again to stop the machine and the blade.
Speed Buttons: Press the button to gradually increase the speed of the blade in
increments of 1%, up to 100%. Press the button to gradually decrease the speed of
the blade in increments of 1%, down to 7%. Speed is used to set the blending speed of
the Pulse buttons and the Start/Stop button.
Pre-Set Program Buttons: These buttons, numbered 1 through 6, are pre-
programmed blending cycles designed for the most commonly made drinks.
Depending on the viscosity of the drink you are creating, pressing one of the six Pre-
Set program buttons will run the machine for a full cycle. The machine will stop by
itself when the cycle is complete. A cycle varies in speed and length. Each button can
be reprogrammed to any recipe through custom programming or by reprogramming
to any of the 34 available recipes. Due to difference of recipes, your results may vary.
Display Window: This area, depending on which button is pressed, displays a variety
of operation messages. A "Ready" message appears when there is power to the
machine.
IMPORTANT NOTES!
Start/Stop Button: Pressing one of the Pre-Set program buttons,
while the motor is running, will stop the machine.
Speed Button: These settings will reset if the power is shut off.
Pulse Buttons: The pulse provides a quick increase or decrease in
speed of the blade when blending or refreshing a drink. Press
increase the motor to speeds that range from 51%-100%. Press
to decrease the motor speed down to a range of 50%-7%. The Pulse
button will override the running program as long as it is Pressed.
Once released, the original program continues its cycle.
• The Pulse High ( ) and Low (
Speed buttons. To set, while pressing and holding a Pulse button,
press the Speed or button until the desired motor speed is
reached. The pulse speed will remain at this setting until changed
again with the Speed buttons.
6
p
o n t R o l a n e l
High/Low Pulse
) speed is set by using the
Owner Controls: The control panel is accessible by
activating the Power Switch located on the back of
the motor base while pressing button 2.
• Once the unit powers up, the display will cycle
through three screens. The first indicates the
current program version. The second indicates
which program is running on the machine. The
third will indicate the motor temperature (NORM,
WARM, HOT), and the total hours of operation,
including production and testing. This time can not be cleared. Once this screen is
reached, button 2 can be released.
• Press button 2 within 12 seconds to scroll through the menu settings.
• The first press will reveal the timer. Total operation is recorded in hours, minutes and
seconds; including production and testing. This time cannot be cleared.
• The second press will reveal the name of the program controlling the Pre-Set
buttons. If you are using the Advance
PROGRAM."
• The third press will reveal an option to reset the Pre-Set buttons to the original
factory settings.
The Quiet One® is pre-programmed with an Advance® program which is optimized for
the Advance® container. The program can be customized by using the control panel, or a
programming chip or programmer software kit available from Vitamix®. Call your distributor or
customer service for more information.

Programming Pre-Set Buttons

1. Access the 34 stored programs by activating the power switch located on the
back of the motor base while pressing the High Pulse button. The display will
say "BUTTON SET UP"
2. Press the Speed
you reach the one you want.
3. Press the Pre-Set button that you want to program for the recipe selected.
For Example: If you wanted to program button 1 with recipe #17:
1. After accessing the stored programs as described in
step 1, the display window will say "BUTTON SETUP."
2. Press the Speed button until the screen displays
"Recipe 17."
3. Press the 1 button to apply Recipe 17.
4. Either continue programming the other five
buttons or press the High Pulse button to exit and
to
continue blending.
TEMP
NORM
® settings, this will read "VITA-MIX ADVANCE
p
R o g R a m m i n g
or buttons to scroll through the "Recipe" numbers until
VITA-MIX CORP
VERSION #201
VITA-MIX ADVANCE
PROGRAM #201
COUNT TOTAL
25 100
TIMER HR: MIN: SS
0: 10: 33
1 TO OVERWRITE
CURRENT PROGRAM
BUTTON SET UP
RECIPE 1
BUTTON SET UP
RECIPE 17
BUTTON SET UP
RECIPE 17-------->1
READY