Filter Cartridge Replacement - Omnifilter R1500 Instrucciones De Instalación

Filtro de agua del refrigerador
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

FILTER CARTRIdGE REPLACEMENT

NOTE: The life of the filter cartridge depends on water volume used and
the quality of the feed water. It is recommended that the filter cartridge
be replaced per the operating specifications, or when there is a noticeable
change in taste, odor or flow of filtered water.
Purchase an
OMNIFILTER 1500R or 1750R Cartridge for the system.
Read all instructions before replacing the filter cartridges.
A)
Relieve pressure by turning off water supply to the filter. Dispense
water from water dispenser or T-flush valve until water flow stops.
Place bucket or towel under the system to catch any water drips.
B)
Place hand on filter head assembly to steady the system. Rotate
the filter cartridge 1/4 turn counterclockwise until no resistance is
felt. Pull the cartridge down and straight out from the filter head
assembly.
C)
Place hand on filter head assembly to steady the system. Align
the tab on the back of the filter cartridge with the slot in the filter
head assembly. Slide the cartridge filter up into the filter head
assembly until it can go no further. Rotate the cartridge clockwise
1/4-turn until the cartridge can go no further.
D)
Turn on water and check for leaks. If leaks are found, see
troubleshooting section in manual, or call OMNIFILTER
Customer Service at 800.937.6664, M – F 7:30 AM–5 PM CST.
NOTE: A water cartridge may contain carbon fines (very fine black
powder). This will be released during your initial flushing.
E)
Flush water through filter for 5 minutes to remove carbon fines.
Check for leaks again before leaving installation.
TROubLESHOOTING
Leaks between filter head assembly
and filter cartridge
1.
Relieve pressure. Turn off the water supply to the filter. Dispense
water from water dispenser or open T-flush valve until water flow
stops. Place bucket or towel under the system to catch any water
drips.
2.
Remove cartridge and inspect o-rings to make sure they are properly
seated and clean.
3.
Install filter cartridge. Place system into operation and check for leaks.
If leaks persist, turn off the water supply and contact OMNIFILTER
Customer Service at 800.937.6664, M – F 7:30 AM–5 PM CST.
Leaks from tubing fittings
1.
Relieve pressure. Turn off the water supply to the filter. Dispense
water from water dispenser or T-flush valve until water flow stops.
Place bucket or towel under the system to catch any water drips.
2.
Depress collet on system or inlet supply adapter tubing fittings and
pull tubing from fitting. Inspect surface of tubing for scratches or
debris. Clean or cut back tubing to access clean surface.
3.
Wet the end of the inlet tubing and press into the inlet fitting of the
system. Ensure the tubing is fully pushed past the fitting o-rings. Place
system into operation and check for leaks. If leaks persist, turn off
the water supply and contact OMNIFILTER Customer Service at
800.937.6664, M–F 7:30 AM–5 PM CST.
• 4 •
C
B
A
B
T-flush Valve
Installation of a T-flush valve is recommended
when this system is used with an icemaker. The
T-flush valve is installed between the system and
the dispenser, so it can be used to flush away
carbon fines or release pressure before removing
the cartridge.
The T-flush valve can also be installed after plastic
or copper tubing is connected to outlet.
Filter outlet
To water dispenser/
icemaker
When using a drain, pro-
vide an air gap between
end of tube and drain to
prevent contamination. If
a drain is not available, a
bucket can be used.
Air gap
Drain
A
B

Publicidad

Tabla de contenido
loading

Tabla de contenido