Using The French Fries Disc - Silvercrest SKMM 1000 A1 Instrucciones De Servicio

(e.g. oil to prepare mayonnaise) you can use the mini
food pusher 1 with a small opening in the bottom.
5. Place the lid 4 with the food pushers 1, 2, 3 onto the
working container 10. Turn the lid slightly in a clock-
wise direction until it is heard to lock into place.
6. Connect the mains plug 11 to a wall socket.
7. Use the dial 13 to select the desired speed setting.
8. When the process is completed, switch the dial 13 to
0 and pull out the mains plug 11.
9. Turn the lid 4 slightly in an anticlockwise direction
and remove it.
10. Turn the working container 10 slightly in an anti-
clockwise direction and remove it.
11. Remove the axle 18 together with the whisking
disc 8 upwards and remove the prepared food from
the working container 10.
12. Clean all of the accessories that have been used im-
mediately if possible.

11. Using the French fries disc

Application area:
The French fries disc 7 is suitable for cutting French fries
from raw potatoes.
WARNING! Risk of material damage!
Do not apply too much pressure to the French fries
disc 7. Apply an even pressure so that the motor does
not become blocked.
NOTE: for best results, place large potatoes (if necessary
in halves) crossways in the large food chute and press
down with the maxi food pusher 3.
Processing table:
Ingredients max. quantity
Potatoes 500 g
WARNING! Risk of material damage!
Do not operate the device continuously with the French
fries disc 7 in place for more than 2 minutes. After
this, the device must remain switched off until it has
cooled down to room temperature.
Required accessories:
- Working container 10
- Axle 18
- French fries disc 7
- Lid 4 with food pushers 1, 2, 3
And this is how it works:
(For assembly see Figure J)
1. Position the working container 10 on the base
unit 14. Turn the working container slightly in a
clockwise direction until it is heard to lock into place.
2. Place the axle 18 into the working container 10.
70
GB
max.
Switch
processing time
2
approx. 2 min.
3. Place the French fries disc 7 on the axle so that the
French fries blades are positioned upwards.
4. Place the lid 4 with the food pushers 1, 2, 3 onto the
working container 10. Turn the lid slightly in a clock-
wise direction until it is heard to lock into place.
5. Connect the mains plug 11 to a wall socket.
6. Remove the maxi food pusher 3 and fill the pre-
pared, raw potatoes into the food chute no higher
than the MAX mark.
7. Reinsert the maxi food pusher 3.
8. Switch the dial 13 to the 2 position and press the po-
tatoes downwards with the maxi food pusher 3 with
a light, even pressure.
9. Stop (dial 13 in the position 0) before all of the pota-
to pieces in the food chute are processed so that you
can fill in more potatoes.
10. Process all potatoes portion by portion. Empty the
working container 10 from time to time if it is filled
up to the MAX mark.
11. When the process is completed, switch the dial 13 to
0 and pull out the mains plug 11.
12. Turn the lid 4 slightly in an anticlockwise direction
and remove it.
13. Turn the working container 10 slightly in an anti-
clockwise direction and remove it.
14. Hold the axle 18 at the top end and lift it out togeth-
er with the French fries disc 7.
15. Remove the cut French fries from the working contain-
er 10.
16. Clean all of the accessories that have been used im-
mediately if possible.