Noise And Vibrations; Handling Information; Packing Lifting And Transport; Checks Upon Delivery - Lavorwash LAVOR PRO COMFORT M87 Manual Del Usuario

- separate the machine into groups of homogeneous
materials (plastics in accordance with the recycling
symbol, metals, rubber, packing). For parts containing
different materials, contact the competent authorities;
Each homogeneous group must be disposed of in
accordance with recycling laws.
In addition, it is recommended to eliminate those parts
of the machine that may be dangerous, especially for
children.
Before each use, check the machine and, in
particular, check that the battery charging cable and
the connector are in good condition and safe for use.
If they are not in perfect condition, do not use the
machine for any reason until an authorised specialist
repairs the defective parts.
If foam or liquid is noted, immediately turn off the
suction motor.
Do not use the machine on textile flooring, such
as rugs, carpeting, etc.
Wax, foaming detergents or dispersions along the hoses
may cause serious problems for the machine or clog
the hoses.

3.2 NOISE AND VIBRATIONS

See table at page 100.

4. HANDLING INFORMATION

4.1 PACKING LIFTING AND TRANSPORT

During all lifting or transport operations, make sure
that the packed machine is securely anchored to prevent
it from tipping over or falling accidentally.
Transport vehicle loading and unloading operations
must be carried out with adequate lighting.
The packed machine must be handled using adequate
devices, making sure not to damage/strike any part of
the packing, not to tip it over and to be very careful
when placing it on the ground.
All these instructions also apply to the batteries
and the battery charger.

4.2 CHECKS UPON DELIVERY

When the goods are delivered (machine, battery
or battery charger) by the transporter, carefully check
the condition of the p acking and its contents. If the
contents have been damaged, notify the transporter
and reserve the right, in writing (select the word "reserve"
on the document), to submit a claim for compensation
before accepting the goods.

4.3 UNPACKING

Wear safety clothing and use adequate tools to
limit the risks of accidents.
Carry out the following steps if the machine is packed
with a cardboard housing:
- Use scissors or clippers to cut and eliminate the plastic
straps.
- Slip off the cardboard housing from the top of the
packed machine.
- Remove the envelops inside and check their contents
(use and maintenance manual, battery charger
connector)
- Remove the metallic brackets or plastic straps that
secure the machine to the pallet.
26
- Release the brushes and the squeegee from the
packing.
- Take the machine off the pallet (pushing it backward)
by using an inclined surface that is solidly attached to
the floor and to the pallet.
If the machine is packed in a wooden crate:
- Detach all the wooden sides from the pallet, starting
from the top one.
- Remove the protective film wrapped around the
machine.
- Remove the metallic brackets or plastic straps that
secure the machine to the pallet.
- Release the brushes and the squeegee from the
packing.
- Take the machine off the pallet (pushing it backward)
by using an inclined surface that is solidly attached to
the floor and to the pallet.
Take the same precautions and follow the same
instructions to remove the optional battery charger from
the packing (holding the special handles to extract it
from the top of the packing) and the optional battery.
After moving the machine away from all the p acking,
start mounting the accessories and the batteries as per
the instructions provided in the specific section.
Keep all the pieces of the packing since they might be
useful in the future to protect the machine and the
accessories during transport to another location or to
authorised service centres. If not, the packing can be
disposed in accordance with current disposal laws.
4.4 LIFTING AND TRANSPORT: MACHINE, BATTERY
AND BATTERY CHARGER
Never use a forklift truck to lift the machine. There
are no places on the frame that can be used to lift the
machine directly.
Before preparing the p acking and transporting the
machine:
- Empty the recovery tank and the detergent solution
tank.
- Disassemble the squeegee and the brushes or
scrapers.
- Disconnect and remove the batteries.
Place the machine on the original pallet (or an equivalent
one that can bear the weight and is big enough for the
machine's overall dimensions) using an inclined surface.
Solidly anchor the machine and the squeegee to the
pallet using metallic brackets or other elements that
can bear the weight of the parts.
Lift the p allet with the machine and load it on the
transport vehicle.
Secure the machine and the p allet using ropes
connected to the transport vehicle.
As an alternative, when using private transport vehicles,
use inclined ramps to push the machine without the
pallet, making sure to protect all parts and the machine
itself against violent impacts, humidity, vibrations and
accidental movements during transport.
The battery boxes have holes where tools can be
hooked for handling.
To lift or insert the battery (into the machine
compartment), use only suit able personnel and
equipment (cables, eyehooks, etc.) for the operation
and to bear the weight of the loads involved. When