Virutex LPM97S Manual De Instrucciones página 8

E N G L I S H
HAND-HELD DRYWALL SANDER
LPM97S
Important
Read these OPERATING INSTRUCTIONS
and the attached GENERAL SAFETY
INSTRUCTIONS LEAFLET carefully before
using the machine. Make sure you have
understood them before operating the
machine for the first time.
Keep both sets of instructions for any
future queries.
INTENDED USE
The LPM97S dry wall sander has been designed to sand
walls with fillers, ceilings and interior and exterior walls
and to remove remains of carpets, paint coats, linings,
remains of glue and loose plasterwork.
The dry-wall sander should always be used connected
to a vacuum cleaner device.
Users are responsible for any damage and accidents
caused by improper use.
1. SAFETY INSTRUCTIONS FOR OPERATING THE
DRY WALL SANDER
• Always keep your hands a safe distance away from the
rotating sanding disc. The disc could rebound towards
your hands.
• Prolonged exposure to sanding dust from walls can
affect breathing. Always use vacuum cleaner with a
suitable bag fitted for dust from walls and use a suitable
breathing mask.
• Lead paint sanding is highly toxic and should only be
done by specially trained professionals equipped with
special equipment for removing this paint.
• Stand firmly on the ground and keep your balance.
Do not overstretch. Use a suitable platform for the
work carried out.
• Always use suitable safety equipment for sanding,
safety goggles and a breathing mask.
• Never let go of the machine until the disc has fully
stopped. The rotary disc could get caught on the work
surface and knock the machine out of your control.
• Do not leave the machine operating while carrying
it with you. The rotary disc could get caught in your
clothes and cause serious injuries.
• Do not use the machine near inflammable substances,
as the sparks could ignite them.
• The LPM97S sander cannot and must not be used for
abrasive blasting, planing, polishing or sawing. Using
8
the machine for work for which it was not designed is
dangerous and could cause personal injuries.
• Always hold the machine with two hands for sanding.
Losing control of the machine could cause personal
injuries.
• Always grip the device by the insulating handles when
carrying out jobs in which the abrasive disc could come
into contact with hidden electrical cables. Contact with
electrical cables would charge the metal parts of the
machine, causing an electric shock.
• Keep the mains lead away from the machine's working
area. Ensure that the lead remains behind you as you sand.
• Do not use the machine if the lead is damaged. Damaged
leads increase the risk of electric shock.
• Stop the machine immediately if you notice any
unusual vibrations or any other irregularity, and check
the machine until you find the cause.
• The dust produced when working with this machine
could be harmful to your health. Use a good vacuum
cleaner system, wear a suitable breathing mask and pick
up any dust that falls with a vacuum cleaner.
• Never force a machine that appears to have operating
difficulties or shows some sort of weakness. There may
be a technical problem, in which case continuing to work
could damage the machine irreparably. Have the machine
checked by an authorised service centre whenever the
machine is not working properly.
• Use only original accessories.
2. SPECIFICATIONS
Universal motor........................................230 V 50 Hz
Protection level.........................II / double on regulation chart
Power rating.................................................................1,200 W
No-load speed..............................................650-1,300 rpm
Full-load speed.............................................390-780 rpm
Disc diameter..........................................................225 mm
Weight.........................................................................3.1 kg
Weighted equivalent continuous acoustic pressure level
A.........................................................................................82 dBA
Acoustic power level A.................................93 dBA
Uncertainty....................................................................K = 3 dBA
Wear ear protection!
Vibration total values..........................................ah: < 2.5 m/s
Uncertainty.................................................................K: 1.5 m/s
3. CONTENTS STANDARD EQUIPMENT
You will find the following parts inside the case:
• LPM97S hand-held dry wall sander.
• Bayonet connector.
• 1 Abrasive disc grit 80.
• Safety and instruction manuals and miscellaneous
documentation.
2
2