EINHELL GE-LM 36/4in1 Li Manual De Instrucciones Original página 44

not use cleaning agents or solvents; these
may be aggressive to the tool's plastic parts.
Ensure that no water can get inside the tool.
The ingress of water into an electric tool in-
creases the risk of an electric shock.
8.2 General information on maintenance
There are no other parts inside the tool which re-
quire maintenance.
To keep the tool in good working order, carry
out regular maintenance in accordance with the
following instructions. Use only the accessories
and spare parts approved by the manufacturer,
Details can be found in section 8.6 "Ordering spa-
re parts". The use of non-approved accessories or
spare parts can result in very serious injuries.
8.3 Maintenance of the cordless trimmer/scy-
the
8.3.1 Replacing the line spool (Fig. 43-44)
Danger! Remove the batteries!
1. Press the line spool housing together at the
ribbed points marked H and remove the spool
cover.
2. Take out the empty line spool and the pressu-
re spring.
3. Thread the end of the line from the new line
spool through the eyelet (Item K) of the spool
cover and allow approx. 13 cm of line to pro-
ject. Insert the pressure spring (Item L) in the
line spool.
4. Press the spool cover back into the line spool
housing.
8.3.2 Replacing the cutting line
(Fig. 43, 45-46)
Danger! Remove the batteries!
1. Press the line spool housing together at the
ribbed points marked H and remove the spool
cover.
2. Take out the empty line spool and the pressu-
re spring.
3. Remove any remaining cutting line.
4. Insert the new cutting line into the line holder
inside the spool.
5. Keeping the line under tension, wind it up
counter-clockwise.
6. Hook approx. 15 cm of the end of the line
into one of the line holders on the edge of the
spool.
7. Thread the end of the line from the new line
spool through the eyelet (Item K) in the spool
cover. Insert the pressure spring (Item L) in
Anl_GE_LM_36_4in1_Li_SPK9.indb 44
GB
the line spool.
8. Pull sharply on the end of the line to release it
from the line holder.
9. Press the spool cover back into the line spool
housing.
The next time you re-start the tool, the cutting line
will be cut automatically
to the optimum length.
Important! Bits of the nylon line that are cata-
pulted out into the surroundings could cause
injuries!
8.3.3 Sharpening the cutting line blade
(Fig. 9)
The cutting line blade (Item 23c) can become
blunt over time. When you notice this, undo the
screws holding the cutting line blade on the guard
hood. Clamp the blade in a vise. Sharpen the bla-
de with a fl at fi le and make sure that the angle of
the cutting edge is not altered in the process. File
in one direction only.
8.4 Maintenance of the pole-mounted pruner
Use only saw chains and cutter rails approved by
the manufacturer. These are listed in section 4
"Technical data" or are available as accessories
(see section 8.6 "Ordering spare parts"). The use
of spare parts which are not approved by the ma-
nufacturer could result in very serious injuries.
Replacing the saw chain and cutter rail
The cutter rail needs to be replaced if the guide
groove of the cutter rail is worn. Proceed as de-
scribed in the section "Cutter rail and saw chain".
Checking the automatic chain lubrication
You should check the operation of the automatic
chain lubrication system on a regular basis in or-
der to guard against overheating and the damage
this can cause to the cutter rail and the saw chain.
Point the tip of the cutter rail at a smooth surface
(a board or a cut tree face) and allow the pole-
mounted pruner to run. If you see a growing oil
stain on the smooth surface, the automatic chain
lubrication system is working properly. If no clear
oil trace is evident then please refer to the corre-
sponding instructions in "Troubleshooting guide"!
If the information contained there still fails to re-
medy the situation, please contact our service de-
partment or another similarly qualifi ed workshop.
Danger! Do not actually touch the surface. Keep
a safe distance (approx. 20 cm).
- 44 -
20.11.2020 08:35:36