Remote Controller Specifications; Function Buttons - Daitsu APD-9CR Manual Del Usario

CAUTIONS
- Do not mix old and new batteries or batteries of a different type.
- Do not leave the batteries in the remote controller if it is not going
to be used for 2 or 3 months.
- Dispose of the old batteries in the special containers to be found
in the sales outlets.

Remote Controller Specifications

Model RG51B1/(C)EU, RG51B14/(C)E,RG51B31/(C)E
RG51B/(C)EU, RG51B16/(C)E,RG51B31/(C)EU
RG51B17/(C)EU, RG51B18/(C)E,RG51B32/(C)EU
RG51B19/(C)E-M, RG51B20/(C)E,RG51B30/(C)EU
RG51B25/(C)E, RG51B26/(C)EU;RG51B27/(C)E,
RG51B30/(C)E.
Rated Voltage 3.0V(Dry batteries R03/LR03 2)
Lowest Voltage of 2.0V
CPU Emitting Signal
Signal Receiving 8m
Range
Environment -5ºC 60ºC(-41ºC ~ 140ºF)
NOTE:
Temperature setting display:
Celsius scale( C): RG51B14/(C)E, RG51B16/(C)E,RG51B18/(C)E,RG51B31/(C)
E,RG51B19/(C)E-M, RG51B20/(C)E,RG51B25/(C)E,RG51B27/(C)E,RG51B30/(C)
E.
Fahrenheit scale( F): RG51B/(C)EU, RG51B1/(C)EU, RG51B17/(C)EU,RG51B26/
(C)EU, RG51B30/(C)EU,RG51B32/(C)EU,RG51B31/(C)EU.
Perfomance Feature
Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only model without), and FAN.
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17C~30 C(62OF~88OF).
4. Full function of LCD (Liquid Crystal Display)
NOTE: All the illustrations in this manual are for explanation purpose only. Your air
conditioner may be slightly different.The actual shape shall prevail.
17

Function buttons

1. TEMP DOWN Button
Push this button to decrease the indoor temperature
setting in 1ºC(2ºF) increments to 30ºC(88ºF).
2. TEMP UP Button
Push this button to increase the indoor temperature
setting in 1ºC(2ºF) increments to 17ºC(62ºF).
3. MODE Button
Each time the button is pressed, the operation
mode is selected in the sequence of the following:
Model: RG51B14/(C)E,
RG51B16/(C)E,
RG51B18/(C)E,
NOTE: Heat mode is for Cooling & Heating models only.
RG51B19/(C)E-M,
4. SWING Button(on some models)
RG51B20/(C)E
Used to stop or start louver movement and
RG51B31/(C)E
set the desired up/down airflow direction.
RG51B30/(C)E.
5. RESET Button
NOTE:
Once the recessed RESET button is pressed,
- RG51B16/(C)E ,RG51B18/(C)E
all of the current settings will be cancelled
models have no SWING feature;
and the controller will return to the initial settings.
- RG51B18/(C)E ,RG51B19/(C)
E-M, RG51B20/(C)E models
6. ON/OFF Button
have no LED DISPLAY feature.
Operation starts when this button is pressed
- RG51B19/(C)E-M model has no
and stops when the button is pressed again.
MED FAN feature.
7. FAN SPEED Button
- RG51B31/(C)E model
Used to select the fan speed in four steps:
ECONOMY button is instead of
SLEEP button.
- RG51B30/(C)E model has no
- Some models have no MED FAN feature.
MED FAN and SWING features
8.TIMER ON Button
Press this button to activate the Auto-on time setting.
Each press will increase the time setting in 30 minutes
increments, up to 10 hours, then at 1 hour increments up
to 24 hours. To cancel the Auto-on time setting, just press
the button until
the time setting is 0.0.
9. ECONOMY(SLEEP) Button
Select this function during the sleeping time. It can
Model: RG51B25/(C)E;
maintain the most comfortable temperature and save
RG51B27/(C)E.
energy. This function is available on COOL, HEAT or
NOTE:
AUTO mode only .
RG51B25/(C)E model has no
SWING feature.
> AUTO > COOL > DRY > HEAT > FAN
> Auto -> Low > Med > High
18