Shutoff Clutch - Ingersoll Rand 3RL-EU Serie Instrucciones

Shutoff Clutch

Separate the Clutch Housing Assembly from the Gear Case.
Remove the Shutoff Clutch from the Clutch Housing
Assembly.
Mark or take note of the location (setting) of the Clutch
Adjusting Nut.
Relieve the Clutch Spring tension by rotating the Clutch
Adjusting Nut until it lightly touches the rear Spring Seat
Stop. Pull the Clutch Ball Seat down against the Clutch
Spring and work some Ingersoll–Rand No. 67 Grease
around the Clutch Cam Balls, the cam, Clutch Ball Seat,
and the Thrust Bearings. Remove the Ball Retaining Ring.
Work some grease into the hole made by removing one
Bevel Pinion Bearing Ball.
Adjust the Clutch Adjusting Nut to its original setting and
assemble the tool.
Model Torque
Device
3RLL2S3–EU shutoff
3RLM2S3–EU shutoff
3RLN2S3–EU shutoff
3RLO2S3–EU shutoff
3RLL2C3–EU cushion
3RLM2C3–EU cushion
3RLN2C3–EU cushion
3RLL2S5–EU shutoff
3RLM2S5–EU shutoff
3RLQ1S5–EU shutoff
3RLN2S5–EU shutoff
3RLO2S5–EU shutoff
3RLL2C5–EU cushion
3RLM2C5–EU cushion
3RLN2C5–EU cushion
3RLL2D5–EU stall
3RLM2D5–EU stall
3RLN2D5–EU stall
H
Tested in accordance with ANSI S5.1–1971 at free speed
♦
Tested in accordance to ISO8662–1 at free speed
PLACING TOOL IN SERVICE
SPECIFICATIONS
Torque Range Free
(Soft Draw) Speed
90 psi pressure
in–lbs (Nm) rpm
5.0–19.0 (0.6–2.2)
3.5–30.0 (0.4–3.4)
2.0–46.0 (0.2–5.3)
2.0–60.0 (0.2–6.8)
5.0–19.0 (0.6–2.2)
3.5–30.0 (0.4–3.4)
2.0–46.0 (0.2–5.2)
5.0–19.0 (0.6–2.2
3.5–30.0 (0.4–3.4)
7.0–45.0 (0.8–5.1
2.0–46.0 (0.8–5.1)
2.0–60.0 (0.2–6.8)
5.0–19.0 (0.6–2.0)
3.5–30.0 (0.4–3.4)
2.0–46.0 (0.2–5.2)
20 (2.3)
31 (3.5)
48 (5.4)
MAIN LINES 3 TIMES
AIR TOOL INLET SIZE
TO
AIR
SYSTEM
TO
AIR
TOOL
LUBRICATOR
REGULATOR
BRANCH LINE 2 TIMES
AIR TOOL INLET SIZE
DRAIN REGULARLY
Square
Drive
in. Pressure
1,800 1/4 – – –
1,100 1/4 – – –
700 1/4 72.5
500 1/4 71.7
1,800 1/4 – – –
1,100 1/4 – – –
700 1/4 72.4
1,800 1/4 – – –
1,100 1/4 – – –
500 1/4 71.7
700 1/4 72.5
500 1/4 71.7
1,800 1/4 – – –
1,100 1/4 – – –
700 1/4 72.4
1,800 1/4 – – –
1,100 1/4 – – –
700 1/4 70.8
4
FILTER
COMPRESSOR
(Dwg. TPD905–1)
♦Vibrations
HSound Level
dB (A)
Power
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
Level
2
m/s
– – –
– – –
0.8
0.5
– – –
– – –
1.0
– – –
– – –
0.5
0.8
0.5
– – –
– – –
1.0
– – –
– – –
0.7