Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
16
SPECIFICATIONS
GENERAL
Type:
Compact disc player
Disc type:
Standard compact discs (12 cm discs), CD-TEXT
CD-R, CD-RW discs
NOTE: Finalized CD-R or CD-RW discs can be played back in this unit.
Dimensions:
Player unit:
Installation:
Table top type
Mass:
Player unit:
Power supply:
U.S.A., Canada and Taiwan R.O.C. models: 120 V AC ±10%, 60 Hz
European models:
Power consumption:
18 W
Environmental conditions:
Operational temperature: 5 to 35° C
Operational humidity:
Storage temperature:
AUDIO SECTION
Main out, Monitor out
Quantization:
24-bit linear per channel
Sampling frequency:
44.1 kHz at normal pitch
Oversampling rate:
8 times
Total harmonic distortion:
0.01% or less
Signal to noise ratio:
90 dB or more
Channel separation:
85 dB or more
Frequency response:
20 to 20,000 Hz
Analog output
Output level:
2.0 V r.m.s.
Load impedance:
10 kΩ/kohms or more
Digital output
Signal format:
SPDIF
0.5 Vp-p 75 Ω/ohms
Output level:
FUNCTIONS
Instant start:
Within 20 msec.
Variable pitch:
±4% (0.05% pitch), ±10% (0.1% pitch), ±16% (0.1% pitch)
±24% (0.1% pitch), ±100% (1.0% pitch)
Pitch bend:
Pitch range ±32%
Pitch range ±100%:
Sampler
Sampling:
44.1 kHz
Length:
15 sec.
Output level:
2.0 V r.m.s. (Variable / -14 ~ +6 dB)
Variable pitch:
±24% (0.1% pitch)
Search precision:
1/75 sec. (1 subcode frame)
Max. scan speed:
Over 20 times normal speed
Max. MEMO memory steps:
5000 steps
✽ Specifications and design are subject to change without notice for purpose of improvement.
26
However, according to recording quality, some CD-R/RW discs
cannot be played.
285 (W) x 111.5 (H) x 327 (D) mm (without feet)
11-7/32" (W) x 4-25/64" (H) x 12-7/8" (D)
5.7 kg (12 lbs 9 oz)
230 V AC ±10%, 50 Hz
(41 to 95° F)
25 to 85%
(no condensation)
– 20 to 60° C (4 to 140° F)
±99%
17
REPLACING THE BELT
• On the DN-S5000, the platter is driven by a belt.
In the unlikely case of trouble, use the procedure described below to replace the belt.
1. Remove a screw
A
(Hexagon socket head) and
pull out Scratch Disc and Slip Mat.
(Hexagon socket head)
2. Remove Belt from Motor Pully.
Belt
Motor Pully
3. Remove 3 screws
(< head) and pull out
B
Platter.
4. Remove Belt from Platter.
Platter
Belt
5. Mount in the order 4 → 1.
CAUTIONS:
• Unplug the power cord before replacing the
belt.
• Do not touch the sensor or scale(∗) when
removing the Platter.
• Do not apply oil or grease to the belt when
replacing it.
Stabilizer
A
Scratch Disc
Slip Mat
Slip Sheet
B
(< head)
B
(< head)
Platter
∗
Publicidad
Tabla de contenido
