Specifications; Intended Use Of The Pipe Milling Machine; At A Glance; For Your Safety - Fein RSG Ex 1500 A Manual Del Usuario

3 41 01 261 06 0.book Seite 18 Montag, 16. April 2018 12:03 12
en
18
Original Instructions.

Specifications.

Electric pipe milling machine:
Reference number
Type* RSG Ex 1500 A (**) RSG Ex 1500 B (**)
Reference number
Type RSG 1500 A (**)
Voltage (U)
Frequency (f)
Mains supply 3 ~ (three-phase current)
No-load speed (n )
0
Motor
Cutting tools
Advancement (f)
Rated power (P)
Length of the mains cable (with plug)
RSG Ex 1500 A/B (**)
RSG 1500 A/B (**)
Weight (m), approx.
Class of protection
Protective type
Dimensions:
Max. tool Ø
L
max.
H
max.
B
max.
B
1
B
2
L
1
*Electromotor and auxiliary switch in explosion-proof design
The A-weighted sound level of the pipe milling machine in the typi-
cal case is:
Sound pressure level 92 dB (A); sound power level 105 dB (A).
Wear ear protection
Pneumatic pipe milling machine:
Reference number
Type RDG 1500 A (**)
Air pressure (p)
Air consumption under
load (Q)
No-load speed (n )
0
Motor
Cutting tools
Advancement (f)
Power output (P)
Hose diameter
Weight (m), approx.
Dimensions:
Max. tool Ø
L
max.
H
max.
B
max.
B
1
B
2
L
1
The A-weighted sound level of the pipe milling machine in the typi-
cal case is:
Sound pressure level 103 dB (A); sound power level 116 dB (A).
Wear ear protection!
Measuring values are determined according to EN 62 841.
7 360 ... 7 360 ...
7 360 ... 7 360 ...
RSG 1500 B (**)
400 V
50 Hz
2860 r.p.m.
35 r.p.m. 70 r.p.m.
40 mm/min 80 mm/min
1500 W
2 x 20 m
10 m
73 kg
/ I
IP X4
220 mm
980 mm
340 mm
450 mm
372 mm
205 mm
795 mm
7 560 ... 7 560 ...
RDG 1500 B(**)
6 bar
72 l/s
6000 r.p.m.
35 r.p.m. 70 r.p.m.
40 mm/min 80 mm/min
2000 W
15 mm
67 kg
220 mm
980 mm
280 mm
450 mm
372 mm
205 mm
795 mm

Intended use of the pipe milling machine.

The pipe milling machine is intended for cutting free pipe ends and
installed pipes sections of sufficient stability, made of steel or cast
iron, as well as for chamfering pipe ends prior to welding them at
construction sites or in the open. The pipe milling machine is for
specialty companies and to be operated by specialists; it is not inten-
ded for continuous everyday use.
EU Directive 94/9EU ATEX (Atmosphères Explosibles)
We should like to point out that the Fein pipe milling machines of
type RDG (**) / RSG (**) / RSG Ex (**) have not been approved
for use in areas where there is risk of explosion and that there are
no EC type-approval certificates in accordance with the 94/9EC
Directive for these pipe milling machines.
(In the case of pipe milling machine type RSG Ex (**), where the
electromotor and the auxiliary switch are concerned, merely two
ATEX-conform components are built in.)
The ATEX Directive is only valid for the EC countries.

At a glance.

1 Clamping unit
2 Fixation screw for side plate
3 Side plate
4 Information labe
5 Bolt
6 Threaded spindle
7 Feed unit
8 Fillister head screw for feed unit
9 Tight-fit screw
10 Running axle
11 Clamping lever
12 Hexagon screw
13 Disc
14 Tensioning axle
15 Nut
16 Tool spindle holder
17 Pipe nut
18 Fixation screw for motor
19 Fish plate
20 Chain wheel
21 Transport shaft
22 Securing ring
23 Pin
24 Screw plug, tool spindle holder
25 Carrying handle
26 Depth scale
27 Knurled nut
28 Feed switching lever
29 Hexagon of chain tensioner
30 Washer of chain tensioner
31 Securing screws of chain tensioner

For your safety.

Before using this pipe milling machine please first read the fol-
lowing and act accordingly:
this Instruction Manual,
the relevant national industrial safety regulations.
This instruction manual should be kept for later use and enclosed
with the pipe milling machine, should it be passed on or sold.