Contact Information; Installationsvejledning; Installation Af Detektoren - Interlogix VE1120 Serie Hoja De Instalación

UL/cUL VE1120 only.
The product must be connected to a listed burglar
system compatible control unit or power supply
unit, which provides a minimum 4 hours of
standby power and has a voltage output between
10 and 15 VDC.
All wiring must be made according to National
Electrical Code, NFPA70, and CSA C22.1,
Canadian Electrical Code Part I, Safety Standards
for Electrical Installations.
Perform walk test at least one per year.
Use only a listed power-limited supply.
FCC Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the
equipment and receiver
•
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected
•
Consult the dealer or an experienced
radio/TV technician for help
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
IC This Class B digital apparatus complies with
Canadian ICES-003.
European Union UTC Fire & Security hereby declares that this
directives device is in compliance with the applicable
requirements and provisions of the Directive
2014/30/EU and/or 2014/35/EU. For more
information see www.utcfireandsecurity.com or
www.interlogix.com.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/

Contact information

www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.utcfssecurityproducts.eu
6 / 36
DA: Installationsvejledning
Beskrivelse
VE1120 serien indeholder:
• VE1120 PIR bevægelse detektor
• VE1120AM PIR bevægelse detektor med anti-mask
De har patenteret spejl, pyro og signalbehandlingsteknologi.

Installationsvejledning

Den anvendte teknologi i disse detektorer er modstandsdygtig
over for falske alarmer. Undgå imidlertid mulige årsager til
ustabilitet (se Figur 1), f.eks.:
• Direkte sollys på detektoren
• Kraftig træk på detektoren.
•
Varmekilder inden for detektorens synsfelt
•
Dyr inden for detektorens synsfelt
•
Blokering af detektorens synsfelt med store genstande
som f.eks. møbler
•
Genstand under 50 cm (20 in.) fra anti-maskeringsdetektor
(AM)
•
Installation af to detektorer mod hinanden og mindre end
50 cm (20 in.) fra hinanden (kun AM-detektorer)

Installation af detektoren

Figur 7
(1) Standardtilslutning (fabriksstandard)
Dobbelt sløjfe-tilslutning
(2)
CP Central
WT Gangtest
AM Antimaskning
D/N Dag/nat
Rtest Fjernbetj test
Sådan installeres detektoren:
Tag dækpladen af og fjern skruen (se Figur 2, trin 1).
1.
Åbn forsigtigt detektoren med en skruetrækker (Figur 2,
2.
trin 2 og 3).
Gør soklen fast til væggen. Til fladmontering anvendes
3.
mindst to skruer (DIN 7998) i position A. Til
hjørnemontering anvendes skruer i position B eller
C (Figur 3). Til at installere vægsabotagekontakt anvendes
position A eller C.
4. Tilslut detektoren (se figur 3 og 7).
Vælg de ønskede jumper- og DIP-switch-indstillinger (se
5.
figur 5). Se "Jumper-indstillinger" på side 7, hvis du ønsker
yderligere oplysninger.
Fjern afskærmningen og påsæt klæbemærker efter behov
6.
(se eksempel i Figur 6).
7. Til loftsmontering med 90 graders anvendelse benyttes
SB01-svingmonteringskonsol.
Luk frontlågen.
8.
Isæt skruen og anbring dækpladen.
9.
Til EN 50131 Grade 3-installationer må
monteringsposition B ikke anvendes.
P/N 146279999-2 (ML) • REV H • ISS 11MAR19