Worx WG117 Manual Del Usuario página 12

foot and pull upward on the Telescopic shaft
(6). Then rotate the Telescopic shaft clockwise
90 degrees (See Fig. E3) and release; the Shaft
will be locked in position automatically
(see Fig. e4).
4. adJuSTING THE auxIlIaRy HaNdlE
(See Fig. F)
1) The auxiliary handle's bracket can be moved
up or down on the shaft and the auxiliary
handle itself can be moved forward or
backward into 4 different locked positions
(see Fig. F).
2) When the handle is in desired position, turn
knob and tighten securely.
5. aTTaCHING ExTENSIoN CoRd
(See Fig. G)
An extension cord retainer is built into the
Rear Handle (1) that prevents the cord from
coming unplugged. To use this feature, simply
double the extension cord about 8 inches
(203mm) from the end, forming a small loop.
Insert this loop into the slot on the back of the
handle. Hook the end of the loop over the tab.
12
Gently tug on the cord to insure that it is firmly
retained in the trimmer's handle. Plug the
receptacle end of the extension cord into the
Plug Insert (3) in the trimmer.
6. adJuSTMENT oF TRIMMER HEad
aNGlE (See Fig. H1,H2)
To adjust the trimmer head angle downwards,
put one foot on the motor housing, then
grip the Rear Auxiliary handles, and apply
adequate force to adjust, as shown in Fig. H1.
To adjust the trimmer head angle upwards,
put one foot on the safety Guard (4), then
grip the Rear and Auxiliary handles and apply
adequate force to adjust, as shown in Fig. H2.
7. uSING THE oN/oFF TRIGGER
Press and hold the on/off trigger to start the
trimmer. Release to stop.
8. TRIMMING
Hold the bottom of the trimmer head just above
the ground and at a slight angle. Allow only the
tip of line to make contact with the grass. Let
the trimmer line work at its own pace; do not
force the trimmer line into the work area.
2-in-1 Grass Trimmer/Edger
9. EdGING
First, rotate the Rear Handle (1) 90 degree
clockwise (see "Main Handle Rotation" ,
Fig. e3 & e4).
Adjust the trimmer head angle to be the
lowest horizontal setting (see "Adjust the
trimmer head angle to the lowest horizontal
setting" , Fig. H1). Then position the edger
Wheel (8) on the ground for edge mode
(see Fig. I). There are two white lines, located
on each end of the safety Guard (4), that show
the cutting plane of the trimmer line. Align
these marks with the edge of your lawn.
while edging, allow the tip of the line
to make contact. do not force the line.
The wheel helps to prevent the unit from
touching the ground. Take extra caution
while edging as objects can be thrown
from the trimmer line.
10. auToMaTIC lINE FEEd SySTEM
When initially switching on the trimmer, a
small length of line is fed out.
A 'clattering' noise will be heard for a short
time. This is normal and is caused by the line
being cut by the line cutter. Once the line is
cut to the correct length, the 'clattering' noise
will stop and the trimmer motor will run at full
speed.
To feed more line, stop the trimmer
completely, then restart, allowing the motor
to reach full speed. Repeat this until you hear
the 'clattering' noise of the line cutting. (Do not
repeat this procedure more than 6 times)
11. MaNually FEEdING THE lINE
(See Fig. J)
Press and release the Line Feed Button (15)
(See Fig. J) whilst gently pulling out on one of
the lines until it has reached the line cutter.
When the required amount of line is fed out,
gently pull on the second line (there is no need
to press the Line Feed Button again). If the line
extends past the line cutter, too much line has
been fed out.
If too much line is fed out, remove the spool
cap and click the spool counter-clockwise until
the line is at the desired length.
EN