Tool Specifications - Skil 4750 Manual De Instrucciones

4. Power tool use and care
while working, do not touch the cord, but imme-
a) Do not force the power tool. Use the cor- diately disconnect the plug Never use tool when
rect power tool for your application. The cor- cord is damaged; have it replaced by a qualified
rect power tool will do the job better and safer. person.
b) Do not use the power tool if the switch does
• Do not work materials containing asbestos
not turn it on and off. Any power tool that cannot (asbestos is considered carcinogenic).
be controlled with the switch is dangerous and
• Do not use a saw blade which is cracked, de-
must be repaired.
formed or dull.
c) Disconnect the plug from the power source
• Keep hands away from the saw blade while
and/or the battery pack from the power tool
the tool is in use.
before making any adjustments, changing
• Remove all obstacles on top of as well as un-
accessories, or storing power tools. Such
derneath the cutting path before you start cut-
preventive safety measures reduce the risk of
ting
starting the power tool accidentally.
• Always disconnect plug from power source
d) Store idle power tools out of the reach of
before making any adjustment or changing any
children and do not allow persons unfamiliar
accessory
with the power tool or these instructions to
• Take protective measures when during work
operate the power tool. Power tools can cause
dust can develop that is harmful to one's health,
injuries in the hands of untrained users.
combustible or explosive (some dusts are con-
e) Maintain power tools. Check for misalign-
sidered carcinogenic); wear a dust mask and
ment or binding of moving parts, breakage of
work with dust/chip extraction when connect-
parts and any other condition that may affect
able.
the power tools operation. If damaged, have
• Wear protective goggles when working with
the power tool repaired before use. Accidents
materials which produce chips.
are caused by poorly maintained power tools.
• Avoid damage that can be caused by screws,
f) Keep cutting tools sharp and clean. Prop-
nails and other elements in your workpiece; re-
erly maintained cutting tools with sharp cutting
move them before you start cutting.
edges are less likely to bind and are easier to
• Check the functioning of the tool before each
control.
use and, in case of a defect, have it repaired im-
g) Use the power tool, accessories and tool
mediately by a qualified person; never open the
bits etc. in accordance with these instruc-
tool yourself.
tions and in the manner intended for the par-
• When used outdoors, connect the tool via a
ticular type of power tool, taking into account
fault current (FI) circuit breaker with a triggering
the working conditions and the work to be
current of 30 mA maximum, and only use an
performed. Use of the power tool for opera-
extension cord which is intended for outdour
tions different from those intended could result
use and equipped with a splashproof coupling-
in injuries.
socket.
• The noise level when working can exceed 85
5. Service
dB(A); wear ear protection.
a) Have your power tool serviced by a quali-
• When you put away the tool, switch off the
fied repair person using only identical re-
motor and ensure that all moving parts have
placement parts. This will ensure that the safety
come to a complete standstill.
of the power tool is maintained.
• SKIL can assure flawless functioning of the
b) The substitution of the brushes cable of
tool only when original accessories are used.
the power tool should be accomplished by
• Use completely unrolled and safe extension
an authorized and qualified technical service.
cords with a capacity of 16 Amps (U.K. 13
Brushes out of specification can cause damages
Amps).
to the motor of the power tool.
• In case of electrical or mechanical malfunction,
Safety instructions for Jig Saws immediately switch off the tool and disconnect
the plug.
• Always keep the cord away from moving parts
• This tool should not be used by people under
of the tool If the cord is damaged or cut through
20
the age of 16 years.
WHEN CONNECTING NEW 3-PIN PLUG (U.K.
ONLY): This tool is intended for making cut-throughs
and cut-outs in wood, plastic, metal, ceramic
• Do not connect the blue (= neutral) or brown
plates and rubber, and is suitable for straight
(= live) wire in the cord of this tool to the earth
and curved cuts with mitre angles to 45°
terminal of the plug
• If for any reason the old plug is cut off the cord
Read and save this instruction manual
of this tool, it must be disposed of safely and not
left unattended
Safety Warnings for Laser Machines
A Wheel for adjusting sawing speed
B Locking button for on/off switch
• Caution – The use of other operating or
C On/Off switch
adjusting equipment or the application
of other processing methods than those D Handle
E Wrench
mentioned here, can lead to dangerous ra-
F Vaccum connection*
diation exposure.
G Adjusting lever orbital action
• Never make warning signs on the machine
H Base plate
unrecognisable.
I
J
Laser Radiation
K SDS clamping lever for saw blade release
Do not stare into beam
L Locking screw
Class 2 laser product
M Contact protector
N Dust cover for vacuuming*
Do not direct the laser beam at
O Laser light on/off button
persons or animals and do not
P Saw blade
stare into the laser beam yourself,
not even from a distance. Q Stroke rod
R Roller guide
This power tool produces laser
class 2 laser radiation according to EN 60825-1.
* The accessories illustrated or described are
Other persons could be blinded unintentionally.
not included as standard delivery.
• Do not use the laser viewing glasses as

Tool Specifications

safety goggles. The laser viewing glasses are
used for improved visualisation of the laser
Jig Saws
beam, but they do not protect against laser ra-
Order Number
diation.
Input Power
• Do not use the laser viewing glasses as sun
Amperage 127 V – 60 Hz
glasses or in traffic. The laser viewing glasses
do not afford complete UV protection and
Stroke rate at no load
Stroke
reduce colour perception.
Cutting
• Do not allow children to use the power tool
Performance
without supervision. They could unintentionally
blind other persons.
Bevel Cuts
• Shut the laser beam off for stationary op-
Base
eration of the machine. In stationary operation
Weight
Procedure 01/2003
you can easily be blinded by the laser beam.
Protection class
• Do not use any magnifying optical tools
(such as magnifying glasses, telescopes or
* The initial speed can present variations of +/-
binoculars) to view the laser beam 400 /min.
21
Introduction
Machine Elements
Sliding shoe*
Parallel guide
4750
F 012 4750
[W]
750
[A] 6,2
[A] 3,6
220 V – 50 or 60 Hz
[/min] 800* ... 3.000
[mm] 18
[mm]
Wood 80
Aluminium [mm] 10
[mm]
Steel 8
[°] 0 - 45
[mm] x [mm]
184 x 93
[kg] 2,4
according to EPTA
/ II