Step 1 Remove Packaging; Step 2 Install Water Lines - Monogram ZKBSN720NSS Instrucciones De Instalación

STEP 1 REMOVE PACKAGING

WARNING
The refrigerator is much heavier at the top than at the
bottom—be careful when moving. When using a hand
truck, handle from the side only.
AVERTISSEMENT
basculement Le réfrigérateur est beaucoup plus lourd en
haut qu'en bas. Il faut être prudent lors des déplacements. Si
un diable est utilisé, il faut soulever le réfrigérateur sur le côté
seulement.
ADVERTENCIA
El refrigerador es mucho más pesado en su parte superior
que en su parte inferior – tenga cuidado al moverlo. Al usar
un carro manual, sosténgalo de costado únicamente.
• Carefully cut banding at the top and
bottom, remove the outer carton.
• Slide out the back corner posts (2).
• Slide the carton off the top of the
cabinet.
NOTE: IT IS NOT NECESSARY
TO LAY THE CABINET DOWN IN
ORDER TO REMOVE THE SKID!
• The unit is secured to the skid with
4 slotted tie-down straps. Remove
the four 5/16" bolts from the base channels in the tie-
downs.
• Remove the four 7/16" bolts securing the straps to the
skid.
NOTE: DO NOT ATTEMPT TO ROLL UNIT OFF SKID.
• The support blocks on the bottom of the refrigeration
case must be removed before the refrigerator is taken
off the skid or damage will occur. Carefully tilt the
refrigerator and slide the blocks out from beneath.
• Remove the tape from the leveling legs.
• Lift the refrigerator off the skid with an appliance dolly.
Handle from the sides.

STEP 2 INSTALL WATER LINES

Connect to potable water supply
WARNING
only.
AVERTISSEMENT
Raccordez l'appareil à une ali-
mentation d'eau potable seulement.
ADVERTENCIA
Realice la conexión a un sumi-
nistro de agua potable únicamente.
• A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 40 and 120 p.s.i. (275-827 kPa).
INSTALLATION INSTRUCTIONS
Tip Over Hazard.
Risque de
Riesgo de Caídas
STEP 2 INSTALL WATER LINES
• Route 1/4" OD copper or SmartConnect ™ plastic
tubing between house cold water line and the water
connection location.
• Tubing should be long enough to extend to the front of
the refrigerator. Allow enough tubing to accommodate
bend leading into the water line connection.
NOTE: The only Monogram-approved plastic tubing is
supplied in the SmartConnect ™ Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Other
types of plastic may crack or rupture with age and
cause water damage to your home.
SmartConnect ™ Refrigerator Tubing Kits are available
in the following lengths:
2' (.6 m) - WX08X10002
8' (2.4 m) - WX08X10006
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the
line of water.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
• Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into a
bucket. Shut off water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in
many water supply kits, but are not recommended for
this application.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle
valves are illegal and use is not permitted in
Massachusetts. Consult with your licensed plumber.
If the water supply to the refrigerator is from
a Reverse Osmosis Water System, use the
refrigerator's filter bypass plug. Using the
refrigerator's water filtration cartridge with the RO
filter can result in hollow ice cubes.
Filter Bypass Plug
6
Floor
Waterline
Tubing
15' (4.6 m) - WX08X10015
25' (7.6 m) - WX08X10025
31-1000414 Rev. 1