Programming Your Machine - Krups XP4050 Manual Del Usuario

• Press your choice of coffee size by pressing
the respective coffee selection button
(9) (10).
• When the programmed quantity is reached,
espresso stops running automaticly.
• Remove the filter holder and the filter from
the machine and take out the coffee
grounds (14).
The filter basket can be refilled to make more
espressos.
Caution: if the water container is empty
and the pump is running, you will hear a
very distinct noise, which is louder than
the normal operating sound. If this
happens, press the start/stop switch (4).
Check the water container and refill as
needed.
Never let the machine run when the
water container is empty as this can
damage the pump.
U
SING THE SPECIAL
"E.S.E.", which stands for "Easy Serving
Espresso", is a selected measure of coffee,
ground and pressed between two filter papers
making a coffee pod which is ready to use (for
example "illy  pods). This system makes it
easy for you to prepare your espresso and to
clean the machine.
The E.S.E. system was designed for making
Italian-style "espresso ristretto" or "short
espresso".
We do not intend, or recommend, that
the E.S.E. servings be used for making
more then one single serving or a "long
espresso".
We recommend that you take care when
handling and storing the E.S.E. pre-portioned
pods so that they do not become deformed.
For best results, we recommend that you pre-
heat the accessories (filter holder, filter basket
and cups) without any coffee. To do this, see
section entitled "Espresso Making" above.
. Preparing an espresso:
• Fill the water tank (1) (2) (3) and turn on the
machine (4).
Setting the E.S.E. pod (18).
Tear excess paper from pod at perforated
edge. Place the E.S.E. pod with the RED
MARKING FACE DOWN (bend the paper
10
" E.S.E. "
FILTER
corners down) in the E.S.E. filter holder fitted
with its own filter.
or
• Take care to put all the paper inside the filter
or you may have some drips.
Placing the E.S.E. pod correctly will create a
richer, thicker crema.
Locking the handle tightly and properly will
also help avoid leakage from the filter holder
and ensure a better brewing cycle.
Place the filter holder inside the brewing head
and firmly turn the handle as far right as
possible (6) (7) (8).
As soon as the coffee selection buttons
commence to glow continuously, the machine
is ready to operate.
• Press the single serving coffee button
• When the recommended quantity of coffee
has been reached (35ml), press the coffee
button (9) again if suitable volume was
not preprogrammed.
• Remove the filter holder from the brewing
head and throw away the used coffee pod.
NOTE: All pods (such as those sold by
Starbucks  and Illy ) can be used in your
Krups XP 4050 as long as they are E.S.E.
standard pods.
illy  is a registered trademark of illy espresso of the
americas, inc.
Starbucks  is a registered trademark of the
Starbucks Coffee Company
2. P
ROGRAMMING YOUR MACHINE
Should you wish to alter the preprogrammed
quantity (50ml per cup, manufacturing
setting) of espresso filled into one or two
cups, proceed as follows:
• Fill the water container (1) (2) (3) and turn
on the machine (4).
• Put the filter basket for one or two cups into
the filter holder (5).
• Place some ground coffee in the filter basket
(1 or 2 measuring scoops), and then tamp it
down firmly; the coffee should reach the lip
of the filter (11) (12) or a E.S.E. pod in the
E.S.E. filter (18).
• Remove any ground coffee which is lying
around the filter (13).
• Replace the filter holder (6) (7).
(9).
.
: