Tabla de contenido
Publicidad
SPARE PARTS LIST FKS-210L
REF.NR.
DESCRIPTION
5
CARBON BRUSH HOLDER
6
CARBON BRUSH SET (2 PCS)
7
CARBON BRUSH CAP
10
STATOR
14
BALL BEARING 607 Z
15
ROTOR
16
BALL BEARING 6000 Z
43+44
SWITCH + CAPACITOR
55
GEAR
59
BALL BEARING 6001 ZZ
74
INNER FLANGE
78
LASER
66
FERM NR.
409400
CIRCULAR SAW
409401
409402
THE NUMBERS IN THE FOLLOWING TEXT
409403
CORRESPOND WITH THE PICTURES AT PAGE 2
800607
TECHNICAL SPECIFICATIONS
409404
806000
Voltage
409414
Frequency
Power input
409416
No load speed
806001
Saw blade dimensions
Number of teeths
409410
Weight
409418
Lpa (sound pressure level)
Lwa (sound power level)
aw(vibration value)
PRODUCT INFORMATION
Fig. A.
1. Handgrip
1A.Extra handgrip
2. Type plate
3. On/off switch
4. Handle to set sawing depth
5. Power cord
6. Riving knife
7. Saw blade safety guard
8. Hexagonal bolt
9. Soleplate
10. Flange
11. Saw blade
12. Rip fence
13. Rip fence clamping knob
14. Handle to set sawing angle
-
Shaft lock (Fig. C3)
UNPACKING
The circular handsaw is shipped with:
1 Rip fence
1 TCT Saw blade Ø 210 mm
1 Box spanner
Check first whether or not the delivery has been
damaged by transport and/or whether all the parts are
present.
SAFETY INSTRUCTIONS
The following pictograms are used in these instructions
for use:
Ferm
Ferm
| 230 V~
| 50 Hz
| 1800 W
| 5000/min.
| 210x30x2.4 mm
| Z40
| 6,4kg
| 97,2 dB(A)
| 110,2 dB(A)
| 1.138 m/s
2
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
Faulty and/or discarded electrical or electronic
apparatus have to be collected at the appropriate
recycling locations.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
ELECTRICAL SAFETY
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Keep these instructions in a safe place!
Always check that the power supply corres-ponds
to the voltage on the rating plate.
The machine is double insulated in accordance
with EN50144; therefore no earth wire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
BEFORE USING THE CIRCULAR SAW:
•
Check the following points:
•
does the voltage of the motor correspond with the
mains voltage (appliances for a mains voltage of 230 V
•
are the mains lead and the mains plug in a good
condition: solid, without any loose ends or damage;
•
is the saw blade missing any teeth or showing
any cracks, it so must be replaced immediately.
•
Make sure the blade is secure.
•
Use this circular saw to saw only wood, wood-like
products.
•
Do not use circular saw blades wich are deformed or
damaged.
•
Do not use HSS blades.
•
Only use blades meeting the required dimensions, as
well as data and descriptions;
Never apply any blades of which the thickness is
greater than that of the riving knife.
•
Do not stop the blade of a circular saw by pressing
the blade from the side.
•
Check that the blade guard can freely move and fully
closes.
•
Never lock-up the guard in the open position.
•
Never put sideward pressure on the blade. This may
cause the blade to break.
•
Be careful when cutting wood with knots, nails or
cracks in it and/or dirt on it, as these can cause the
blade to get stuck.
3
Publicidad
Tabla de contenido
