Westin 27-1525 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
SURE-GRIP
EQUIPO DE MONTAJE
OPTIONAL LIGHT
JEU DE MONTAGE
27-1525
MOLDED SURE-GRIP
STEP BOARDS
27-6130
BOARDS
27-0010 27-6135
27-0015 27-6530
ITEM QTY
CONTENTS -
1,2 2 STEP BOARD, PASSENGER (1) AND DRIVER (2) (SOLD SEPARATELY)
3 4 FRONT/CENTER BRACKET
4,5 2 REAR BRACKET, PASSENGER (4) AND DRIVER (5)
6 6 5/16-18 X 1.00" HEX HEAD BOLT
7 12 5/16-18 X .75" SQUARE HEAD BOLT
8 18 5/16" FLAT WASHER
9 6 5/16" LOCK WASHER
10 12 5/16-18 NYLOCK NUT
11 6 EXTRUDED U-NUT
12 8 3/8-16 X 1.00" HEX HEAD BOLT
13 16 3/8" FLAT WASHER
14 8 3/8" LOCK WASHER
15 8 3/8-16 HEX NUT
1,2 2 ESTRIBOS, ACOMPAÑANTE (1) CONDUCTOR (2) (SE COMPRA SEPARADO)
3 4 SOPORTE DELANTERAS-CENTERAL
4,5 2 SOPORTE TRASERAS, LADO DEL ACOMPAÑANTE (4) Y EL CONDUCTOR (5)
6 6 PERNOS CON C4BEZA HEXAGONAL DE 5/16-18 X 1,00"
7 12 PERNOS CON CABEZA CUADRADA DE 5/16"
8 18 ARANDELAS PLANAS DE 5/16"
9 6 ARANDELAS DE PRESIÓN DE 5/16"
10 12 TUERCA PRESIÓN DE 5/16"
11 6 TUERCA A PRESIÓN EN "U"
12 8 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 1,00"
13 16 ARANDELAS PLANAS DE 3/8"
14 8 ARANDELAS DE PRESIÓN DE 3/8"
15 8 TUERCAS HEXAGONALES DE 3/8-16
1,2 2 MARCHE-PIEDS, PASSAGER (1) ET CONDUCTEUR (2) (ACHETE SEPAREMENT)
3 4 SUPPORTS AVANT/CENTRAL
4,5 2 SUPPORTS ARRIERE, COTE PASSAGER (4) ET COTE CONDUCTEUR (5)
6 6 BOULONS A TETE HEXAGONALE 5/16-18 X 1,00 PO
7 12 BOULON A TETE CARREE 5/16 PO
8 18 RONDELLES PLATES 5/16 PO
9 6 RONDELLES A FREIN 5/16 PO
10 12 ECROU A FREIN 5/16 PO
11 6 ECROU EN U EXTRUDE
12 8 BOULONS A TETE HEXAGONALE 3/8-16 X 1,00 PO
13 16 RONDELLES PLATES 3/8 PO
14 8 RONDELLES A FREIN 3/8 PO
15 8 ÉCROUS HEXAGONAUX 3/8 PO
STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning. It is strongly
recommended to install the Sure Grip Gap Strip for these vehicle applications.
STEP 2. Locate mounting locations as shown.
STEP 3. Install u-nuts as shown.
Attach mounting brackets as shown. Hand tighten.
STEP 4.
STEP 5. Insert square head bolts as shown (3 in each slot, 6 per board).
NOTE: For lighted boards, run wiring harness prior to attaching board to brackets (refer to Step 8)
wire harness on passenger side.
STEP 6. For Sure-Grip Running Boards, slide closure strip as shown. Set lights (if purchased) in appropriate location. Attach to Sure-Grip Running Board
as shown. SEE FIGURE 7.
Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners. Recommended torque values are 10
STEP 7.
FT.LBS. for 5/16" square head fasteners, 15 FT. LBS for 5/16" fasteners and 26 FT.LBS. for 3/8" fasteners.
NOTE: For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps
8-9.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS
USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH OR
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2004-09 FORD F-150 SUPER CAB (EXCLUDES HERITAGE)
APPLICACION: 2004-09 FORD F-150 SUPER CAB
APPLICATION: 2004-09 FORD F-150 SUPER CAB (
KIT
27-6000
1
CONTENIDO - CONTENU
SEE FIGURE 1.
SEE FIGURE 2.
Drill hole through plastic strip and run wires as shown.
( NO SE INCLUYEN EL MODELO
3
SEE FIGURES 3-6.
SEE FIGURES 8 AND 9.
HERITAGE)
SAUF LES MODELES
4
TOOLS-HERRAMIENTA-OUTILS
1/2" SOCKET
1/2" WRENCH
9/16" SOCKET
RATCHET
TORQUE WRENCH
DADO DE 1/2"
LLAVE DE TUERCAS DE 1/2"
DADO DE 9/16"
MANERAL
LLAVE DE TORQUE
DOUILLE 1/2 PO
CLE 1/2 PO
DOUILLE 9/16 PO
CLIQUET
CLE DE COUPLE
. SEE FIGURES 8,9, AND 10
SEE FIGURE 10.
SEE FIGURE 11.
WO: 75-0708 REVISION D 10/14/08
HERITAGE)
5
. Run longer