Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
MOLDED STEP BOARDS
EQUIPO DE MONTAJE
EXT. CAB 27-0000, 27-0005
JEU DE MONTAGE
D-CAB 27-0010, 27-0015
27-1615
EXT. CAB 27-6120, 27-6125,
SURE-GRIP
OPTIONAL LIGHT
D-CAB 27-6130, 27-6135
KIT
27-6000
ITEM
QTY
CONTENTS -
1,2
2
STEP BOARD, PASSENGER (1) AND DRIVER (2) (SOLD SEPARATELY)
3,4
2
FRONT BRACKET, PASSENGER (3) AND DRIVER (4)
5,6
4
CENTER / REAR BRACKET, PASSENGER (5) AND DRIVER (6)
7
12
M8-1.25 X 25MM HEX HEAD BOLT
8
12
5/16-18 X .75" SQUARE HEAD BOLT
9
24
5/16" FLAT WASHER
10
12
5/16-18 LOCK WASHER
11
12
5/16-18 LOCK NUT
1,2
2
ESTRIBOS, ACOMPAÑANTE (1) CONDUCTOR (2) (SE COMPRA SEPARADO)
3,4
2
SOPORTE DELANTERAS, ACOMPAÑANTE (3) Y CONDUCTOR (4)
5,6
4
SOPORTE CENTRAL / TRASERAS, ACOMPAÑANTE (5) Y CONDUCTOR (6)
7
12
PERNOS CON CABEZA HEXAGONAL DE M8-1,25 X 25MM
8
12
PERNOS CON CABEZA CUADRADA DE 5/16-18 X ,75
9
24
ARANDELAS PLANAS DE 3/8"
10
12
ARANDELAS DE PRESIÓN DE 3/8"
11
12
TUERCA PRESIÓN DE 5/16-18
1,2
2
MARCHE-PIEDS, PASSAGER (1) ET CONDUCTEUR (2) (ACHETE SEPAREMENT)
3,4
2
SUPPORTS AVANT, PASSAGER (3) ET CONDUCTEUR (4)
5,6
4
SUPPORTS CENTERAL / ARRIERE, PASSAGER (5) ET CONDUCTEUR (6)
7
12
BOULONS A TETE HEXAGONALE M8-1,25 X 25MM
8
12
BOULON A TETE CARREE 5/16-18 X ,75 PO
9
24
RONDELLES PLATES 5/16 PO
10
12
RONDELLES A FREIN 5/16 PO
11
12
ECROU A FREIN 5/16-18
STEP 1.
Remove contents from box and check for damage. Verify all parts are present. Read and understand instructions before beginning.
NOTE:
Westin does not recommend using closure strip for this application.
Attach mounting brackets as shown. See Figures 1 and 2.
STEP 2.
STEP 3.
Insert square head bolts as shown (3 per slot, 6 per board). See Figures 4 and 5.
attaching board to brackets (Refer to Step 6). See Figures 4, 5 & 8). Run longer wire harness on passenger side.
STEP 4.
For Sure-Grip Running Boards: Set lights (if purchased) in appropriate location. Attach to Sure-Grip Running Board as shown. Attach to
running board as shown. See Figure 3. Drill hole through plastic strip and run wires as shown. See Figure 6.
Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners. Recommended torque
STEP 5.
values are 10 FT.LBS. for 5/16" square head fasteners and 16 FT.LBS. for M8 fasteners.
NOTE:
For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps 6 and 7.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN
RECOMMENDS USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT,
VIBRATION, PINCH OR ROTATION WHEN SECURING HARNESS TO VEHICLE. CAUTION: ALWAYS USE A FUSED(+)
HINT:
Molded Step Boards: For longevity, check rubber seals before installation. Rubber grommets around red and blue wires going into rear
sockets, should be inserted and recessed about 1/4".
Silicone where lights go into socket. Install lights and run wire loom as shown.
center as shown.
SEE FIGURE 5.
STEP 6.
Determine whether your vehicle has a positive or negative switching courtesy system or an auxiliary light source (most Fords). Obtain an
accurate wiring diagram for your vehicle's courtesy light system.
For positive and negative switching:
Locate a pass-through point (usually under carpet at driver side door sill) for the wire harness. Locate main courtesy wire (usually wire lead
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION:
APLICACIÓN:
APPLICATION:
SURE-GRIP BOARDS
27-6520
27-6530
CONTENIDO
- CONTENU
POSITIVE SUPPLY SOURCE. UNDERCOAT SEAL FOR HARSH WEATHER.
NOTE:
2005-08 TOYOTA TACOMA EXTENDED CAB, D-CAB
TOYOTA TACOMA CABINA EXTENDIDA , DOBLE CABINA, MOD. 2005-08
TOYOTA TACOMA CABINE ET ALLONGEE, CABINE DOUBLE, 2005-08
1
Remove bulbs and apply white grease into sockets and replace bulbs. Apply RTV
SEE FIGURE 5.
3
TOOLS-HERRAMIENTA-OUTILS
7/16" SOCKET
7/16" WRENCH
13MM SOCKET
13MM WRENCH
RATCHET
TORQUE WRENCH
DADO DE 7/16"
LLAVE DE TUERCAS DE 7/16"
DADO DE 13MM
LLAVE DE TUERCAS DE 13MM
MANERAL
LLAVE DE TORQUE
DOUILLE 7/16 PO
CLEF 7/16 PO
DOUILLE 13MM
CLEF 13MM
CLIQUET
CLÉ DE COUPLE
NOTE:
For lighted boards, run wiring harness prior to
SEE FIGURE 7.
For Sure-Grip Running Boards, run wire loom down
WO:
75-0713 REVISION A 5/23/07
5
6
4
Publicidad
Manuales relacionados para Westin 27-0000, 27-0005
Resumen de contenidos para Westin 27-0000, 27-0005
- Página 1 For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps 6 and 7. WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH OR ROTATION WHEN SECURING HARNESS TO VEHICLE.
- Página 2 FINISH PROTECTION Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
- Página 3 PROTECTION DE LA FINISSION Les produits Westin ont une finission de haute qualité qui requiert des soins, comme toute autre finission du véhicule exposée aux éléments. Protégez la finission à l’aide d’une cire non-abrasive (par exemple, Pure Carnauba) de façon régulière. L ’usage de tout savon, pâte à polir ou cire contenant un abrasif est nuisible, puisque les composantes strient la finission et la laissent vulnérable à...
- Página 4 FORWAR D FORWAR D DELANT ERA DELANT ERA FORWAR D FORWAR D AVANT AVANT DELANT ERA DELANT ERA AVANT AVANT REAR PASSENGER SHOWN FRONT PASSENGER SHOWN FIGURE 1 FIGURE 1 FIGURE 2 FIGURE 2 LADO DEL ACOMPAÑANTE TRASERAS LADO DEL ACOMPAÑANTE DELANTERAS FIGURA 1 FIGURA 1 FIGURA 2...