Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
MOLDED
STEP
EQUIPO DE MONTAJE
JEU DE MONTAGE
BOARDS
27-0010
27-1875
27-0015
SURE-GRIP
OPTIONAL LIGHT KIT
SURE-GRIP
27-6000
BOARDS
27-6130
27-6135
27-6530
CONTENTS -
ITEM
QTY
1,2
2
STEP BOARD, PASSENGER (1) AND DRIVER (2) (SOLD SEPARATELY)
3
2
FRONT BRACKET
4
2
FRONT/CENTER BRACKET
5
2
REAR/CENTER BRACKET
6,7
2
REAR BRACKET, PASSENGER (6) AND DRIVER (7)
8
16
M8-1.25 X 30MM HEX HEAD BOLT
9
16
3/8" FLAT WASHER
10
16
3/8" LOCK WASHER
11
16
5/16-18 X .75" SQUARE HEAD BOLT
12
16
5/16" FLAT WASHER
13
16
5/16-18 LOCK NUT
1,2
2
ESTRIBOS, ACOMPAÑANTE (1) CONDUCTOR (2) (SE COMPRA SEPARADO)
3
2
SOPORTE DELANTERAS
4
2
SOPORTE DELANTERAS
5
2
SOPORTE TRASERAS
6,7
2
SOPORTE TRASERAS, ACOMPAÑANTE (6) CONDUCTOR (7)
8
16
PERNOS CON CABEZA HEXAGONAL M8-1.25 X 30MM
9
16
ARANDELAS PLANAS DE 3/8
10
16
ARANDELAS DE PRESIÓN DE 3/8
11
16
PERNOS CON CABEZA CUADRAD 5/16-18 X .75"
12
16
ARANDELAS DE PRESIÓN DE 5/16
13
16
TUERCA PRESIÓN DE 5/16-18
1,2
2
MARCHE-PIEDS, PASSAGER (1) ET CONDUCTEUR (2) (ACHETE
SEPAREMENT)
3
2
SUPPORT AVANT
4
2
SUPPORT AVANT/CENTRAL
5
2
SUPPORTS ARRIERE/CENTRAL
6,7
2
SUPPORTS ARRIERE, PASSAGER (6) ET CONDUCTEUR (7)
8
16
BOULON A TETE HEXAGONALE M8-1.25 X 30 MM
9
16
RONDELLE PLATE 3/8"
10
16
RONDELLE A FREIN DE 3/8"
11
16
BOULON A TETE CARREE 5/16-18 X .75 PO
12
16
RONDELLES PLATES 5/16 PO
13
16
ECROU A FREIN 5/16-18
Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning. It is strongly
STEP 1.
recommended to install the Sure Grip Gap Strip for these vehicle applications.
Determine front, front center, rear center and rear brackets. Rear/center bracket has 1 identification hole.
STEP 2.
Attach drivers side brackets to underside of body panel using two M8-1.25 x 30mm hex head bolts, 3/8" flat washers, and 3/8" lock washers
STEP 3.
per bracket. Hand tighten.
Insert square head bolts as shown (4 per slot, 8 per board).
STEP 4.
prior to attaching board to brackets (refer to Step 4) Run longer wire harness on passenger side.
For Sure-Grip Running Boards, slide closure strip as shown. Set lights (if purchased) in appropriate location. Attach to Sure-Grip Running
STEP 5.
Board as shown.
Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners. Recommended torque values
STEP 6.
are 10 Ft.Lbs. For 5/16" hardware and 22 Ft.Lbs. For M8 hardware.
NOTE:
For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps
7-8.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN
RECOMMENDS USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT,
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2008 TOYOTA SEQUOIA
APLICACIÓN:
APPLICATION: 2008 TOYOTA SEQUOIA
1
2
CONTENIDO
- CONTENU
/CENTRAL
/CENTRAL
"
"
"
SEE FIGURE 1.
SEE FIGURE 2.
Drill hole through plastic strip and run wires as shown.
TOYOTA SEQUOIA
SEE FIGURES 3 AND 4 NOTE:
.
SEE FIGURE 6.
, MOD. 2008
3
4
TOOLS-HERRAMIENTA-OUTILS
1/2" SOCKET
1/2" WRENCH
13MM SOCKET
13MM WRENCH
RATCHET
RATCHET EXTENSION
TORQUE WRENCH
DADO DE 1/2"
LLAVE DE TUERCAS DE 1/2"
DADO DE 13MM
LLAVE DE TUERCAS DE 13MM
MANERAL
MANERAL EXTENSION
LLAVE DE TORQUE
DOUILLE 1/2"
CLE 1/2"
DOUILLE 13MM
CLE 13MM
CLIQUET
RALLONGE DE
CLIQUET
CLE DE COUPLE
SEE FIGURE 1.
.
For lighted boards, run wiring harness
SEE FIGURE 5.
WO:
75-0874 REVISION 7/10/08
5
6
7
Publicidad
Manuales relacionados para Westin 27-1875
Resumen de contenidos para Westin 27-1875
- Página 1 For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps 7-8. WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT,...
- Página 2 FINISH PROTECTION Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
- Página 3 PROTECTION DE LA FINISSION Les produits Westin ont une finission de haute qualité qui requiert des soins, comme toute autre finission du véhicule exposée aux éléments. Protégez la finission à l’aide d’une cire non-abrasive (par exemple, Pure Carnauba) de façon régulière. L ’usage de tout savon, pâte à polir ou cire contenant un abrasif est nuisible, puisque les composantes strient la finission et la laissent vulnérable à...
- Página 4 8 9 10 8 9 10 8 9 10 8 9 10 INSTALLATION VIEW OF DRIVER SIDE SHOWN, PASSENGER SIDE OPPOSITE FIGURE 1 VISTA DE LA INSTALACIÓN DEL LADO DEL CONDUCTOR OPUESTO AL LADO DEL ACOMPAÑANTE FIGURA 1 ILLUSTRE: COTE CONDUCTEUR, EN FACE: COTE PASSAGER FIGURE 1 FIGURE 2 FIGURA 2...