Cequent Performance Products 76184 Instrucciones De Instalación página 3

Always wear SAFETY GLASSES
when installing hitch
Access hole
j k
Existing Nuts
Bumper
Fasteners typical both sides
Figure 1
1. Remove Fascia – Open the tailgate. Pry open 4 plastic covers below taillights remove the 4 screws using a 7mm socket, 2 each side.
Remove 2 screws that connect the bottom lower edge of the fascia to the metal support tabs using a T20 socket. Remove 8 screws that
connect the wheel well liner to the fascia using T15 socket, 4 each side. Gently pull back the wheel well trim, remove 2 screws that
connect the fascia to the vehicle body with a 7mm socket, 1 each side. Starting from the wheel well gently pull off fascia. Unplug any
wires that are attached.
2. Remove bumper (support exhaust)– Remove 4 M10 nuts with a 15mm socket from the top bumper attachments, set nuts aside for re-
attachment, 2 each side. Remove 4 M10 bolts with a 15mm socket from the bottom bumper attachments, 2 each side. Be sure to
support the vehicle exhaust system as these bolts also attach the exhaust hangers. Return the bumper and bolts to the vehicle owner.
3. Install hitch – Raise the hitch into position over the bumper studs, install the nuts removed earlier. Raise exhaust hangers into position,
install the M10 bolts n and conical washers o (teeth side toward hitch). Fishwire the carriage bolts j and spacers k into the vehicle
frame through the access hole in the hitch, install the conical washers l (teeth side toward hitch) and nuts m.
4. Torque fasteners - Tighten all ½ GR5" fasteners with torque wrench to 75Lb.-Ft. (102 N*M) and all M10 fasteners to 38Lb.-Ft. (52 N*M)
Proper torque is needed to keep the hitch secure to the vehicle when towing.
5. Re-install fascia - Reverse the process used in step 1 to re-install the fascia. Be sure to reconnect any plugs that were disconnected.
*Vehicle fascia has a removable panel for hitch usage. Panel may be replaced when hitch is not in use.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or
ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2017 Horizon Global™ Corp - Printed in Mexico
Installation Instructions
PART NUMBERS: 76184, 84184, CQT76184
n o
Exhaust Hanger
Conical Washer
Teeth side
Frame rail
Against hitch
l m
Bolt Hole
Access hole
Fish Wire
Example
Sheet 3 of 18 76184NP
Fastener Kit: 76184F
① Qty.(4) Carriage Bolt
1/2"-13 X 1 1/2" GR5
Qty.(4) Spacer
② 1/4" x 1" x 2"
Part No. 5121
③ Qty.(4) Conical washer 1/2''
Part No. 01292008
m Qty.(4) Hex Nut
1/2"-13 GR5
n Qty.(4) Bolt
M10 x 1.5 x 45mm Cl10.9
o Qty.(4) Conical washer 3/8''
Part No. 01292006
p Qty. (4) Fish wire
1/2"
Part No. 5482
8-4-17 Rev. A