Tabla de contenido
Publicidad
Appendix
TROUBLESHOOTING
If you believe your CD player is failing to work properly, check the following troubleshooting table for tips. Sometimes simple mistakes in setup or
operation may appear like serious problems. There are also times when the problem in question may be caused by something else other than your CD
player, and at times like these you should check any other electronic devices being used at the same time.
If the problem in question continues to persist even after checking the troubleshooting table below and taking whatever corrective action is
recommended, contact your nearest Pioneer Service Station or contact the store from which you purchased your player for further assistance.
Description of problem
A disc fails to be ejected even after the
EJECT button (0) has been pressed.
Playback doesn't begin even when a
disc is inserted.
Playback comes to a halt almost
immediately after it begins.
No sound is output.
Sound is distorted or full of noise.
A large amount of noise is generated
when playing back a certain disc or
discs. Playback halts unexpectedly.
Track searching fails to halt with Auto
Cue function turned ON.
The jog dial doesn't work.
The jog dial performs a different
function from that desired.
Back cueing fails to work when the
CUE button is pressed during playback.
Unable to produce loop playback by
pressing the LOOP OUT/OUT ADJ but-
ton.
Unable to perform DJ operations
Auto cue and other settings are not
stored.
WAVE data is not stored.
HOT CUE data is not stored.
Television pictures are distorted or
noise appears in FM broadcasts.
Disc is not rotating even though power
has been turned on.
32
32
<DRB1308>
<DRB1308>
En/Sp
En
Possible cause of problem
÷ Power cord has not been plugged in.
÷ A track is being played back.
÷ EJECT button (0) is broken.
÷ Auto Cue function is turned ON.
÷ Disc has been inserted upside down.
÷ Disc is dirty or covered with condensation.
÷ Audio cable has come loose or has not been
properly plugged in.
÷ DJ mixer is not working properly.
÷ Jacks or jack plugs are dirty.
÷ Player is currently in pause mode.
÷ Audio cable has not been properly plugged in.
÷ Jacks or jack plugs are dirty.
÷ Player is subject to noise from a nearby television
set.
÷ Disc is seriously warped or scratched.
÷ Disc is unusually dusty or dirty.
÷ Track searching sometimes takes longer than
expected when the length of silent portions
between tracks is unusually long.
÷ If the length of a silent portion between two tracks
is longer than 10 seconds in duration, the second
track cannot be played back unless Auto Cue
function is turned OFF.
÷ The DIGITAL MODE switch is set to ON.
÷ The jog mode is incorrect.
÷ No cueing point has been defined.
÷ The DIGITAL MODE switch is set to ON.
÷ No cueing point (i.e., starting point) has been
defined.
÷ The DIGITAL MODE switch is set to ON.
÷ The DIGITAL MODE switch is set to ON.
÷ The power was turned off right after a setting was
made.
÷ The data is stored when playback of the current
track is completed.
÷ The HOT CUE data is stored in memory when the
disc is ejected.
÷ Interference caused by CD player.
÷ Disc rotation is automatically halted when no
operation is performed for 80 minutes or longer
when in pause mode.
÷ When the last track on the disc is over the disc
stops rotating.
Recommended action
÷ Plug in power cord.
÷ Set the player to pause or cue standby mode
before pressing the EJECT button (0).
÷ See p. 8.
÷ Press the PLAY/PAUSE button (38) to begin
play.
÷ Hold the TIME MODE/AUTO CUE button
depressed for 1 second or more to set the
Auto Cue mode to OFF.
÷ Reinsert with label side facing upward.
÷ Wipe disc to remove dust or condensation.
÷ Plug in audio cable properly.
÷ Check switch and volume settings on DJ
mixer.
÷ Wipe away dust or dirt and reinsert plugs.
÷ Press the PLAY/PAUSE button (38) to begin
play.
÷ Connect audio cable to line input jack of DJ
mixer. Do not connect to microphone jack.
÷ Wipe away dust or dirt and reinsert plugs.
÷ Turn off power to television set or move
television set further away from CD player.
÷ Replace with new disc.
÷ Wipe away dust or dirt from disc.
÷ Hold the TIME MODE/AUTO CUE button
depressed for 1 second or more to set the
Auto Cue mode to OFF.
÷ Set the DIGITAL MODE switch to OFF.
÷ Press the JOG MODE button to select the
desired function.
÷ Specify the desired cueing point. (See p. 21.)
÷ Set the DIGITAL MODE switch to OFF.
÷ Specify the desired cueing point. (See p. 21.)
÷ Set the DIGITAL MODE switch to OFF.
÷ Set the DIGITAL MODE switch to OFF.
÷ Wait 10 seconds before turning off the
power after a change.
÷ Wait until playback of the current track is
completed.
÷ Eject the disc. (Then turn off the power.)
÷ Turn off the power to the CD player or move
the player further away from the radio or
television set.
÷ Press the PLAY/PAUSE button (38) to begin
playback. Alternatively, press the EJECT
button (0) to eject the disc.
Publicidad
Tabla de contenido
