Comelit Magis Kit B/W Manual Tecnico página 17

Warning:
• Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the standards in force.
• All the equipment must only be used for the purpose it was designed for. Comelit Group S.p.A. declines any responsibility for improper use of the apparatus, for modifi cations made by
third parties for any reason or purpose, and for the use of accessories and materials which are not originals.
• All the products comply with the requirements of Directive 2006/95/EC (which replaced Directive 73/23/EEC and subsequent amendments), as certifi ed by the CE mark they carry.
• Do not route the riser wires in proximity to power supply cables (230/400V).
• Do not insert objects or pour liquids into the device.
• Installation, mounting and assistance procedures for electrical devices must only be performed by specialised electricians.
• Cut off the power supply before carrying out any maintenance work.
• Connect the module-holder frame to earth (see Fig.).
• Do not press and hold the audio hook while the handset is lifted.
• The camera must not be installed opposite bright light sources, or in places where the fi lmed subject is against the light. To resolve this problem, we
recommend modifying the installation height of the camera, which is usually 160 - 165 cm, to a height of 180 cm and pointing the lens downward so as
to improve fi lming quality.
• Cameras with colour CCD sensor have poorer sensitivity in low light conditions than black/white cameras. We therefore recommend, in dimly lit
environments, that an additional light source is installed.
General information ............................................................................................................................................................................................18
External unit ........................................................................................................................................................................................................18
Art. 4881 ...............................................................................................................................................................................................................18
Art. 1205/B ...........................................................................................................................................................................................................18
Installing the external unit ..................................................................................................................................................................................19
Internal units ........................................................................................................................................................................................................20
Mounting the Magis internal unit .......................................................................................................................................................................20
Removing the monitor ........................................................................................................................................................................................20
Art. 6401E .............................................................................................................................................................................................................21
Description of monitor ........................................................................................................................................................................................21
Art. 2608 ...............................................................................................................................................................................................................22
Installing door-entry phone Art. 2608 ................................................................................................................................................................22
General installation and operating instructions ..............................................................................................................................................23
Operating distances table ..................................................................................................................................................................................23
Operation .............................................................................................................................................................................................................23
Description of button functions and settings ..................................................................................................................................................24
Settings for monitor Art. 6401E and Style door-entry phone ..........................................................................................................................24
TAB. A Riser addresses ......................................................................................................................................................................................24
Description of functions .....................................................................................................................................................................................24
Additional main or secondary monitors ...........................................................................................................................................................25
Default button settings .......................................................................................................................................................................................25
General button programming warnings ............................................................................................................................................................25
Programming buttons for generic or coded actuator ......................................................................................................................................26
Programming for intercom call ..........................................................................................................................................................................26
Programming/deleting intercom address (selective intercom only) ..............................................................................................................26
TAB B Selective intercom addresses ................................................................................................................................................................26
Programming buttons for intercom call ............................................................................................................................................................27
Programming buttons for other functions ........................................................................................................................................................27
TAB C Riser addresses .......................................................................................................................................................................................28
Programming reset .............................................................................................................................................................................................28
Programming range/ringtones ...........................................................................................................................................................................29
Direct programming of intercom call ................................................................................................................................................................30
Monitor ringtone selection .................................................................................................................................................................................30
Special programming - Art. 4881 .......................................................................................................................................................................31
Wiring diagrams:
MSK/018 Basic diagram for two-family kits Art. 8472MB with cascade connection. Switching on/voltage check with system in standby. ........107
MSK/013B Basic diagram for two-family kits Art. 8472MB with branch connection ............................................................................................108
MSK/014B Diagram for two-family kits Art. 8472MB extended with a second Art. 4881. Branch connection. ....................................................109
MSK/014A Diagram for two-family kits Art. 8472MB extended with a second Art. 4881. Cascade connection. ................................................. 110
MSK/018/A Diagram for two-family kit with additional power supply unit Art. 1395 ............................................................................................ 111
MSK/019 Use of remote camera module Art. 1259/A ......................................................................................................................................... 112
SB2/AAQ Connection of video amplifi er Art. 4833/A ........................................................................................................................................... 113
MSK/HA Addition of a main monitor in parallel. Cascade connection ................................................................................................................. 113
MSK/I Addition of a main monitor in parallel. Branch connection ........................................................................................................................ 114
MSK/A9 Branch connection of 1 main monitor and 1 secondary monitor with the same user code ................................................................... 114
MSK/CI Cascade connection of 1 main monitor and 1 secondary monitor with the same user code ................................................................. 115
MSK/AE Connection of additional door-entry phones with branch connection from monitor .............................................................................. 115
MSK/AD Connection of additional door-entry phones with cascade connection from monitor ........................................................................... 116
MSK/F Addition of a parallel door-entry phone, with branch connection from riser ............................................................................................ 116
SB/X3 Use for various purposes of button P1 (Art. 2608) ................................................................................................................................... 117
SB2V/AAK Connection of call repetition devices (Art. 1229 or Art. 1122/A) ....................................................................................................... 117
17 17