Maintenance Table; Tyre Pressure; Check/Top Up Engine Oil; Check / Top-Up (26) (Mod. Honda Gxv 630; 660; 690) - Stiga 4WD Serie Manual Del Usuario

Ocultar thumbs Ver también para 4WD Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

EN
and the key from the main power switch
(12:A)
For the frequency of this intervention
see chapter 13
9 3

Maintenance table

See chapter "13 MAINTENANCE SUM-
MARY TABLE" The table is designed to
help you keep your machine in efficient
and safe working order It indicates the
main operations to be performed and
the frequency of the same Perform the
relative operation described based on
the first deadline to arrive.
9 4

TYRE PRESSURE

Adjust the tyre pressure to meet the values provi-
ded in "0 TECHNICAL DATA TABLE"
9 5

CHECK/TOP UP ENGINE OIL

For this maintenance operation, see
also the manual for the engine sup-
plied with the machine
Always check the oil level before use To
check the level, make sure the machine
is on even ground
The oil level must never exceed the
"FULL" mark This results in the engine
overheating If the oil level exceeds the
"FULL" mark, the oil must be drained
until the correct level is achieved
Change the oil more frequently if the
engine has to operate in demanding
conditions or if the ambient temperatu-
re is high
9 5 1 Check / top-up (26) (Mod Honda GXV
630; 660; 690)
Wipe around the dipstick. Unscrew it and
pull it out. Wipe the dipstick clean.
Insert the dipstick completely without
screwing it in place.
Now pull the dipstick up again. Read off the
oil level.
Top up if the level is lower than the "FULL"
mark (26).
9 5 2 Check / top-up (29; 27) (Mod. B&S 8270;
20
ENGLISH
B&S VANGUARD 18HP)
Wipe around the dipstick. Unscrew it and
pull it out. Wipe the dipstick clean.
Push the dipstick down completely and
screw in place.
Now unscrew and pull the dipstick up again.
Read off the oil level.
Top up if the level is lower than the "FULL"
mark (29; 27).
9 6
CHECKING/TOP-UP THE TRANSMIS-
SION FLUID
For the type of oil to use please refer to "0 TECH-
NICAL DATA TABLE".

9 6 1 Check / top-up (25)

1. Place the machine on a flat surface.
2. Read the fluid level in the reservoir (25:A).
The level should match the line.
3. Top up if necessary.
9 7

BELT DRIVES

check that all the belts are intact.
9 8

STEERING (Model 340 IX)

9 8 1 Checks

Gently turn the steering wheel back and forth.
There must be no mechanical play in the steering
chains.

9 8 2 Adjustment (33)

Adjust the steering chains if required as follows:
1 Put the machine in the straight-ahead position.
2. Adjust the steering chains by means of the
two nuts, located under the central point (33).
3. Adjust both nuts by the same amount until
there is no play.
4. Test drive the machine, moving it forward in
a straight line and checking that the steering
wheel is not off centre.
5. If the steering wheel is off centre, slacken
one nut and tighten the other.
Do not over tension the steering chains
This would make the steering too stiff
and increase wear on the chains
9 9

BATTERY

For the type of battery installed on the machine,
(Translation of the Original Instructions)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Pro 740 ioxPro 540 ixPro 340 ixP 901 ph

Tabla de contenido