Speaker Distance; The Input Assign Menu - Pioneer VSX-521-k Manual De Instrucciones

06 The System Setup menu
06
Adjust the level of each channel using /.
5
If you selected Manual, use / to switch speakers. The
Auto setup will output test tones in the order shown on-
screen:
2c.Channel Level
Front L
Center [
Front R [
Surround R [
Surr. Back R [
Surr. Back L [
Surround L [
Subwoofer [
Adjust the level of each speaker as the test tone is emitted.
Note
• If you are using a Sound Pressure Level (SPL) meter, take
the readings from your main listening position and adjust
the level of each speaker to 75 dB SPL (C-weighting/slow
reading).
• The subwoofer test tone is output at low volumes. You
may need to adjust the level after testing with an actual
soundtrack.
6
When you're finished, press RETURN.
You return to the Manual SP Setup menu.
Tip
• You can change the channel levels at any time by press
, then press CH SELECT and LEV +/– on the
RECEIVER
remote control. You can also press CH SELECT and use
/ to select the channel, and then use / to adjust
the channel levels.
32
En

Speaker Distance

For good sound depth and separation from your system, you
need to specify the distance of your speakers from the
listening position. The receiver can then add the proper delay
needed for effective surround sound.
0dB
1
Select 'Manual SP Setup' from the System Setup menu.
0dB]
0dB]
2
0dB]
Select 'Speaker Distance' from the Manual SP Setup
––– ]
––– ] menu.
0dB]
0dB]
2.Manual SP Setup
Return
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
Adjust the distance of each speaker using /.
3
You can adjust the distance of each speaker in 0.1 feet
increments.
4
When you're finished, press RETURN.
You return to the Manual SP Setup menu.

The Input Assign menu

You only need to make settings in the Input Assign menu if
you didn't hook up your equipment according to the default
settings for the component video inputs.
• Default settings:
Component-1: DVD
-
- Component-2: DVR (DVR/BDR)
Important
• If you connect any source component to the receiver
using a component video input, you should also have your
TV connected to this receiver's COMPONENT VIDEO
MONITOR OUT output (down converting component
video is not possible after assigning an input).
2d.Speaker Distance
10.0 ft
Front L
Center [ 10.0 ft ]
Front R [ 10.0 tt ]
Surround R [ 10.0 ft ]
Surr. Back R [ –––– ]
Surr. Back L [ –––– ]
Surround L [ 10.0 ft ]
Subwoofer [ 10.0 ft ]
Return
Return
If you didn't make component video connections according
to the defaults above, you must assign the numbered input to
the component you've connected (or else you may see the
video signal of a different component). For more on this, see
Using the component video jacks on page 16.
1
Select 'Input Assign' from the System Setup menu.
System Setup
1 . Auto MCACC
2 . Manual SP Setup
3 . Input Assign
4 . Pre Out Setting
5 . HDMI Setup
6 . Auto Power Down
7 . FL Demo Mode
Return
2
Select 'Component Input' from the Input Assign menu.
3.Input Assign 3a.Component Input
Component–1
a.Component Input
Component–2
Return
3
Select the number of the component video input to
which you've connected your video component.
The numbers correspond with the numbers beside the inputs
on the rear of the receiver.
4
Select the component that corresponds with the one
you connected to that input.
Select between BD, DVD, TV (TV/SAT), DVR (DVR/BDR) or
OFF.
• Use / and ENTER to do this.
• If you assign a component input to a certain function, any
component inputs previously assigned to that function
will automatically be switched off.
• Make sure you have connected the audio from the
component to the corresponding inputs on the rear of the
receiver.
5
When you're finished, press RETURN.
You return to the Input Assign menu.
• For the assignment of the digital signal inputs, see
Selecting the audio input signal on page 21.
DVD
[ DVR ]
Return