The System Setup Menu; Using The System Setup Menu; Manual Speaker Setup; Speaker Setting - Pioneer VSX-521-k Manual De Instrucciones

06

The System Setup menu

06
Chapter 6:
The System Setup menu

Using the System Setup menu

The following section shows you how to make detailed
settings to specify how you're using the receiver, and also
explains how to fine-tune individual speaker system settings
to your liking.
Important
• The OSD will not appear if you have connected using the
HDMI output to your TV. Use component or composite
connections for system setup.
• If headphones are connected to the receiver, disconnect
them.
PARAMETER
TOP
MENU
TV
RECEIVER
SLEEP SOURCE CONTROL
RECEIVER DTV/TV
INPUT SELECT
INPUT
HOME
BD DVD TV
MENU
CH
DVR/BDR CD CD R
1
Switch on the receiver and your TV.
Press  RECEIVER to switch on.
2
Switch the TV input to the input that connects this
receiver to the TV through the corresponding composite or
component cable.
3
Press RECEIVER , then press SETUP.
The System Setup menu appears on your TV. Use ///
and ENTER on the remote control to navigate through the
screens and select menu items. Press RETURN to confirm
and exit the current menu.
• Press SETUP at any time to exit the System Setup menu.
30
En
4
Select the setting you want to adjust.
• Auto MCACC – This is a quick and effective automatic
surround setup (see Automatically setting up for surround
sound (MCACC) on page 19).
• Manual SP Setup
- Speaker Setting – Specify the size and number of
speakers you've connected (see below).
Crossover Network – Specify which frequencies will be
-
sent to the subwoofer (page 31).
Channel Level – Adjust the overall balance of your
-
TOOLS VOLUME
MENU
speaker system (page 31).
Speaker Distance – Specify the distance of your
-
ENTER speakers from the listening position (page 32).
• Input Assign – Specify what you've connected to the
component video inputs (see The Input Assign menu on
BAND
SETUP
RETURN
page 32).
MUTE
• Pre Out Setting – Specify how to use the PRE OUT SURR
BACK/FRONT HEIGHT outputs (see The Pre Out Setting
on page 33).
• HDMI Setup – Sets synchronized operations when
connected to a device/TV that supports the Control with
HDMI function (see HDMI Setup on page 34).
• Auto Power Down – Sets to automatically turn off the
power when the receiver has not operated for several
hours (see The Auto Power Down menu on page 33).
• FL Demo Mode – Sets the demo display on the front
panel display (see The FL Demo Mode menu on page 33).
System Setup
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
5.HDMI Setup
6.Auto Power Down
7.FL Demo Mode
Return

Manual speaker setup

This receiver allows you to make detailed settings to optimize
the surround sound performance. You only need to make
these settings once (unless you change the placement of
your current speaker system or add new speakers).
These settings are designed to fine-tune your system, but if
you're satisfied with the settings made in Automatically
setting up for surround sound (MCACC) on page 19, it isn't
necessary to make all of these settings.
CAUTION
• The test tones used in the System Setup are output at
high volume.
Important
• Depending on the Pre Out Setting, there will be
differences in the speaker items that can be adjusted. The
OSD display for these operating instructions is an
example of when the Pre Out Setting is set to Surr. Back.

Speaker Setting

Use this setting to specify your speaker configuration (size,
number of speakers). It is a good idea to make sure that the
settings made in Automatically setting up for surround sound
(MCACC) on page 19 are correct.
1
Select 'Manual SP Setup' from the System Setup menu.
2
Select 'Speaker Setting' from the Manual SP Setup
menu.
2a.Speaker Setting
2.Manual SP Setup
Front
a.Speaker Setting
b.Crossover Network Center
Surr
c.Channel Level
d.Speaker Distance Surr. Back
Subwoofer:
Return
3
Choose the set of speakers that you want to set then
select a speaker size.
Use / to select the size (and number) of each of the
following speakers:
SMALL
[ SMALL ]
[ SMALL ]
[ NO ]
YES
Return