Remote Control - Pioneer VSX-521-k Manual De Instrucciones

01 Controls and displays
01

Remote control

1
RECEIVER
SLEEP SOURCE
2
RECEIVER
INPUT SELECT
3
4
BD DVD TV
DVR/BDR CD CD-R
5
ADAPTER TUNER PORTABLE
VIDEO S.RETRIEVER SIGNAL SEL
6
AUTO/ ALC/
DIRECT STEREO STANDARD
7
AUDIO TUNER EDIT
PARAMETER
TOOLS
TOP
MENU
8
ENTER
9
HOME
MENU
SETUP
RETURN
10
BASS
HDD DVD VCR
1 2 3
SB CH CH SELECT
4 5 6
11
MIDNIGHT SPEAKERS LEV
7 8 9
DIMMER LEV
0
CLR ENTER
+
10
RECEIVER
8
En
As for operating other devices, the remote control codes for
the Pioneer products are preset. The settings cannot be
changed.
12
1 SLEEP
TV
Press to change the amount of time before the receiver
CONTROL
switches into standby (30 min – 60 min – 90 min – Off). You
DTV/TV can check the remaining sleep time at any time by pressing
INPUT
SLEEP once.
13
2  RECEIVER
Switches the receiver between standby and on.
CH
3
RECEIVER
Switches the remote to control the receiver (used to select
the white commands above the number buttons
VOL
(MIDNIGHT, etc)). Also use this button to set up surround
sound (page 30) or Audio parameters (page 28).
14
4 INPUT SELECT
BD MENU
ADV SURR
Use to select the input source (page 21).
5 Input function buttons
MASTER
VOLUME
Use to select the input source to this receiver (page 21). This
MENU
will enable you to control other Pioneer components with the
remote control.
15
6 S.RETRIEVER
Press to restore CD quality sound to compressed audio
sources (page 26).
BAND
7 Listening mode buttons
MUTE
16
AUTO/DIRECT – Switches between Auto surround mode
(page 25) and Stream Direct playback (page 26).
TRE
STEREO – Press to select stereo playback (page 25).
ALC/STANDARD SURR – Press for standard decoding
and to switch between the modes of 2 Pro Logic II, 2
17
DISP
Pro Logic IIx, 2 Pro Logic IIz and NEO:6, and the Auto
EQ
CH level control stereo mode (page 25).
PHASE
ADV SURR – Switches between the various surround
CH
SHIFT modes (page 26).
18
Press BD first to access:
BD MENU* – Displays the disc menu of Blu-ray Discs.
8 System Setup and component control buttons
The following button controls can be accessed after you have
selected the corresponding input function button (BD, DVD,
etc.).
RECEIVER
Press first to access:
AUDIO PARAMETER – Use to access the Audio options
(page 28).
SETUP – Press to access the System Setup menu
(page 30).
RETURN – Confirm and exit the current menu screen.
Press BD, DVD or DVR/BDR first to access:
TOP MENU – Displays the disc 'top' menu of a Blu-ray
Disc/DVD.
HOME MENU – Displays the HOME MENU screen.
RETURN – Confirm and exit the current menu screen.
MENU – Displays the TOOLS menu of Blu-ray Disc player.
Press TUNER first to access:
TUNER EDIT – Memorizes stations for recall (page 24),
also used to change the name (page 24).
BAND – Switches between AM, FM ST (stereo) and FM
MONO radio bands (page 24).
9 /// (TUNE /, PRESET /), ENTER
Use the arrow buttons when setting up your surround sound
system (page 30). Also used to control Blu-ray Disc/DVD
menus/options.
Use TUNE / can be used to find radio frequencies and
PRESET / can be used to select preset radio stations
(page 24).
10 Component control buttons
The main buttons (, , etc.) are used to control a
component after you have selected it using the input function
buttons.
The controls above these buttons can be accessed after you
have selected the corresponding input function button (BD,
DVD, DVR/BDR and CD). These buttons also function as
described below.
Press RECEIVER first to access:
BASS –/+, TRE –/+ – Use to adjust Bass or Treble.
• These controls are disabled when the listening mode is
set to DIRECT or PURE DIRECT.