Pioneer BDP-88FD Manual De Instrucciones página 57

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Problem
• No sound is output.
• Sound is not output
properly.
Left/right audio channels are
inverted or only one side is
produced.
Multi-channel sound is not
output.
Noise can be heard when
outputting DTS Digital Audio
signals from the DIGITAL
OUT terminal.
192 kHz or 96 kHz digital
audio signals cannot be
output from the DIGITAL
OUT terminal.
Secondary audio or
interactive audio is not
output.
Check
Is the volume set to the
minimum?
Is the disc played back in
slow motion?
Is the disc played back in fast
forward or fast reverse?
Are the audio cables properly
connected?
Is the audio cable damaged? If the cable is damaged, replace it with a new one.
Is Audio Output properly
set?
Are the connected
components (AV receiver or
amplifier, etc.) properly set?
Is HDMI Audio Out properly
set?
Is the output video resolution
properly set?
Is a DVI device connected?
Is the HDMI Mode set
appropriately?
Is the DIRECT function set to
ON?
Are the audio cables properly
connected?
Is the audio output of the
connected AV receiver or
amplifier, etc., properly set?
Is multi-channel sound
selected?
Is the connected AV receiver
or amplifier compatible with
DTS Digital Surround?
Is HDMI Audio Out properly
set?
Are Digital Output properly
set?
Remedy
If the volume of the TV or AV amplifier is set to the minimum, raise it.
No sound is output during slow motion play and forward and reverse
scanning.
• Connect the cable properly according to the connected devices
(page 17).
• Insert the cable firmly and all the way in.
• If the connection plug or terminal is dirty, wipe it clean.
Set Audio Output properly, according to the connected device
(page 43).
Read the operating instructions for the connected components and
check the volume, input, speaker settings, etc.
Set HDMI Audio Out to Re-encode or PCM. (page 44).
Switch the resolution at which the video and audio are output by
pressing RESOLUTION /.
The sound will not be output from the HDMI OUT terminal if a DVI
device is connected. Connect the device to a DIGITAL OUT terminal or
the AUDIO OUT terminals (page 21).
• For some BDs, audio signals are only output from DIGITAL OUT
terminal or the HDMI OUT terminal.
• The sound may not be output for discs containing sound other than
audio signals or non-standard sound.
• When copy-protected discs are played, the picture or sound may not
be properly output. This is not a malfunction.
Set the HDMI Mode properly, according to the connected device
(page 44).
Audio output does not occur from the HDMI or DIGITAL AUDIO OUT
terminals if the DIRECT function is set to On. Turn the DIRECT function
off to output audio from the HDMI or DIGITAL AUDIO OUT terminals
(page 30).
Check whether the audio cables for the left and right channels are
inverted or whether the cable for one side is disconnected (page 21).
Read the operating instructions for the connected AV receiver or
amplifier and check the audio output settings of the AV receiver or
amplifier.
Use the menu screen or AUDIO to switch the disc's sound to multi-
channel.
If an AV receiver or amplifier that is not compatible with DTS Digital
Surround is connected to the DIGITAL OUT terminal, set Digital
Output to PCM (page 43).
• Copyright-protected audio is converted to 48 kHz or less before
output.
• Set Max Sampling Frequency to 96KHz or 192KHz (page 43).
When listening to the sound from an HDMI OUT terminal, set HDMI
Audio Out to PCM (page 44).
When listening to the sound from an DIGITAL OUT terminal, set
Digital Output to Re-encode or PCM (page 43).
09
57
En

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Bdp-85fd

Tabla de contenido