Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Installing the Mulch Plug (If equipped)
WARNING
Never operate this rider without either the mulch plug or
deck chute installed.
1.
Remove the wing knobs (a) installed on
the mowing deck and retain for later
installation. See Figure 2-9.
(a)
(b)
(c)
(f)
(g)
(e)
(d)
Figure 2-9
2.
Install the mulch plug (b) into the deck
discharge opening on the deck. The rear of
the mulch plug (b) should be under the tab (f)
on the rear deck bracket (g). The studs (c) on
the deck surface will fit through the holes
on the upper portion of the mulch plug (b).
The small tab (d) on the deck lip area will
fit through the square cutout on the lower
portion of the mulch plug (b). See Figure 2-9.
Important: Make certain that the upper-rear
portion of mulch plug (b) is depressing
the safety switch (e) located on the deck
surface and under the tab (f) on the rear
deck bracket (g). The blade(s) will not start
without the mulch plug (b) properly in
place.
3.
Secure the mulch plug (b) by tightening the
wing knobs (a) removed in step 1.
Installing the Bumper (If equipped)
1.
Remove the two screws (a) as shown in
Figure 2-10.
(b)
(a)
(a)
Figure 2-10
2.
Position the bumper (b) over the mounting
holes and secure using the screws (a)
removed in Step 1. See Figure 2-10.
Tire Pressure
Equal tire pressure should be maintained at all times. Never
exceed the maximum inflation pressure shown on the
sidewall of the tire.
The recommended operating tire pressure is:
•
10 psi for the rear tires
•
14 psi for the front tires
Important: Refer to the tire sidewall for exact
rating of the tire or maximum psi. Do not
(a)
overinflate. Uneven tire pressure could cause the
cutting deck to mow unevenly.
Charging the Batteries
California Proposition 65
(c)
This product contains a chemical known to the State of
California to cause cancer and reproductive harm. Wash
hands after handling.
The batteries contain corrosive fluid and toxic material —
HANDLE WITH CARE. Keep away from children. Do not puncture,
disassemble, mutilate, or incinerate. Explosive gases could
be vented during charging or discharging. Charge in a well
ventilated area, away from sources of ignition.
Recharge only with the charger provided with this rider. A
charger that is not suitable for this machine may damage
the batteries or create the risk of fire.
Do not charge or operate the rider in the rain or in wet conditions.
Rechargeable batteries degrade with time and use.
The batteries may eventually need to be replaced. To
have the batteries replaced, contact your authorized
service dealer.
1.
Lift the charge port door (a), located on the
rear body panel of the mower. See Figure 2-11.
WARNING
WARNING
WARNING
WARNING
WARNING
(a)
(c)
(b)
Figure 2-11
2.
Insert the charging cord (b) into the charge
port (c). Plug charger cord (b) into wall outlet.
See Figure 2-11.
Note: It will take approximately 4 hours to
fully charge the batteries.
Note: The Vehicle Control Module (VCM) LED's
will blink continuously when charging and the
LCD display will display percentage of charge.
The battery is completely charged when
all green lights are illuminated and the LCD
displays 100%. Refer to the Operator's Manual
for more charging tips.
Note: When the charging cord is plugged
into the rider and not yet plugged into the
wall, the LED's will illuminate continuously
until the cord is plugged into the wall.
3.
If at any time you get a charger fault
when charging your battery, follow these
procedures:
a.
Turn the power key off.
b.
Unplug the charger from the rider.
c.
Unplug the charger from the power
source.
d.
Plug the charger back into the power
source.
e.
Plug the charger back into the rider.
f.
It the problem persists contact
qualified service personnel.
Battery Charging Tips
•
Use only the battery charger provided with
this rider.
•
The batteries should be fully charged before
the initial use.
•
Never charge a frozen battery.
•
It is recommended that the rider be charged
once every month during off-season
storage.
•
Always disconnect battery charger (or
extension cord, if used) from the electrical
outlet first, then disconnect battery charger
from the charging port.
•
It is recommended that the batteries be fully
charged after each use. Storing batteries
in a discharged state could reduce future
performance.
•
It will take approximately 4 hours to fully
charge the batteries. Leaving the batteries
connected to the charger for more than 4
hours will not damage the batteries.
•
The batteries do not develop a memory and
do not need to be fully discharged before
recharging.
S
2 — A
& S
ection
SSembly
et
-U
9
p
Publicidad
Capítulos
Tabla de contenido
