Troubleshooting Guide - Zoeller 314-0002 Instrucciones De Instalación

Manufacturer warrants, to the purchaser and subsequent owner during
the warranty period, every new product to be free from defects in material
and workmanship under normal use and service, when properly used
and maintained, for a period of one year from date of purchase by the
end user, or 18 months from date of original manufacture of the product,
whichever comes first. Parts that fail within the warranty period, one year
from date of purchase by the end user, or 18 months from the date of
original manufacture of the product, whichever comes first, that inspections
determine to be defective in material or workmanship, will be repaired,
replaced or remanufactured at Manufacturer's option, provided however,
that by so doing we will not be obligated to replace an entire assembly,
the entire mechanism or the complete unit. No allowance will be made
for shipping charges, damages, labor or other charges that may occur
due to product failure, repair or replacement.
This warranty does not apply to and there shall be no warranty for any
material or product that has been disassembled without prior approval
of Manufacturer, subjected to misuse, misapplication, neglect, alteration,
accident or act of nature; that has not been installed, operated or main-
tained in accordance with Manufacturer's installation instructions; that
has been exposed to outside substances including but not limited to the
following: sand, gravel, cement, mud, tar, hydrocarbons, hydrocarbon
derivatives (oil, gasoline, solvents, etc.), or other abrasive or corrosive
substances, wash towels or feminine sanitary products, etc. in all pump-
ELECTRICAL PRECAUTIONS- Before servicing a pump, always shut off the main power breaker and then unplug the
pump. Make sure you are not standing in water and are wearing insulated protective sole shoes. Under flooded conditions, contact your
local electric company or a qualified licensed electrician for disconnecting electrical service prior to pump removal.
A. Pump will not begin
pumping or retain prime
after operating, or stops
pumping water
B. Pump will not start or
run
C. Flow rate is too low
D. Seal leaks
LIMITED WARRANTY
TROUBLE SHOOTING GUIDE
1. Air leak in inlet line
2. Fittings not tight
3. Hose kinked or looped
4. Inlet hose out of water
5. Clogged inlet
6. Inlet lift too high
7. Impeller blocked
8. Worn seal
1. Blown fuse
2. Low line voltage
3. Worn brushes
4. Impeller blocked
5. Defective motor
1. Piping or hose is kinked or damaged
2. Low line voltage
3. Too much discharge hose friction
1. Worn seal
2. Pump head loose on motor
© Copyright 2016 Zoeller
ing applications. The warranty set out in the paragraph above is in lieu
of all other warranties expressed or implied; and we do not authorize
any representative or other person to assume for us any other liability in
connection with our products.
Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky
40211, Attention: Customer Support Department to obtain any needed
repair or replacement of part(s) or additional information pertaining to
our warranty.
MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPE-
CIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH
OF EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OF
MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THE
EXPRESSED WARRANTY.
Some states do not allow limitations on the duration of an implied war-
ranty, so the above limitation may not apply to you. Some states do not
allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
1. Repair or replace inlet line, make sure fittings are air tight, use
Tefflon tape if necessary
®
2. Tighten fittings air tight, use Tefflon
3. Straighten hose
4. Submerge inlet hose end
5. Clean inlet
6. Lower pump
7. Remove blockage
8. Replace seal
1. If blown, replace with proper sized fuse or reset cirtuit breaker
2. If voltage is under 108 volts, check wiring size
3. Replace brushes
4. Remove blockage
5. Replace pump
1. Clean or replace
2. If voltage is under 108 volts, check wiring size
3. Shorten and/or increase diameter of hose.
1. Replace seal
2. Ensure proper assembly and no obstructions, tighten bolts
Co. All rights reserved.
®
2
tape if necessary
®