Stanley Fatmax V20 Traducción De Las Instrucciones Originales página 6

ENGLISH
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the
charger will begin to charge automatically when the cell
temperature warms up or cools down.
Note: To ensure maximum performance and life of lithium-ion
battery packs, charge the battery pack fully before first use.
Plug the charger (14) into an appropriate outlet before
u
inserting battery pack (13).
The green charging light (14a) will blink continuously
u
indicating that the charging process has started.
The completion of charge will be indicated by the green
u
charging light (14a) remaining ON continuously. The
battery pack (13) is fully charged and may be removed
and used at this time or left in the charger (14).
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Charger LED Modes
Charging:
Green LED Intermittent
Fully Charged:
Green LED Solid
Hot/Cold Pack Delay:
Green LED Intermittent
Red LED Solid
Note: The compatible charger(s) will not charge a faulty
battery pack. The charger will indicate a faulty battery pack by
refusing to light.
Note: This could also mean a problem with a charger. If the
charger indicates a problem, take the charger and battery
pack to be tested at an authorized service centre.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot or too cold,
it automatically starts a Hot/Cold Pack Delay, the green LED
(14a) will flash intermittently, while the red LED (14b) will
remain on continuously, suspending charging until the battery
has reached an appropriate temperature.
6
(Original instructions)
The charger then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
Battery state of charge indicator (Fig. B)
The battery includes a state of charge indicator to quickly
determine the extent of battery life as shown in figure B. By
pressing the state of charge button (13a) you can easily view
the charge remaining in the battery as illustrated in figure B.
Installing and Removing the Battery Pack (not
supplied) from the tool
To install battery pack (not supplied) (Fig. C)
Insert battery pack firmly into tool until an audible click is
u
heard as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (not supplied) (Fig. C)
Depress the battery release button (13b) as shown in
u
figure C and pull battery pack out of tool.
Attaching vacuum hose (Fig. D)
The vacuum hose (8) will need to be attached to the
vacuum before using the appliance.
Place the vacuum on a flat, firm surface.
u
Unlatch tank latches (5) and remove power head from
u
the tank. Remove the hose (8) from the tank.
Align the hose end (15) with the intake port (17) on the
u
front of the appliance, ensuring the hose alignment lock
(16) is aligned with the arrow (17) on the intake port.
Insert the hose end into the intake port and twist
u
clockwise to lock in place.
Replace power head onto the tank and secure latches.
u
Note: The power head will only fit onto the tank when the
intake port on the front of the power head and the storage
area for the wide nozzle tool on the tank are aligned as
shown in figure D.
Correct hand position
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main
u
handle (2).
Use
On / Off Switch (Fig. E)
Attach the appropriate accessory to the hose (8).
u
Insert battery pack (not supplied).
u
To turn vacuum on, press the I/O (on/off) button (1).
u