Panasonic DC-FZ80 Guía Rápida

ENGLISH
Digital Camera
Model No.
DVQW1127ZA
Quick Guide for 4K Photo
Catching the moment you really want ([4K Burst] / [4K Burst(S/S)] / [4K Pre-Burst])
You can take burst pictures of approximately 8 million pixels with a burst rate of 30 fps. You can select and save a frame from the burst file.
1
Recording with the 4K Photo function
1
Press [ ] button
2
Press to select the recording method and press [MENU/SET]
For capturing the best shot of a fast-moving subject (e.g., sports, aeroplanes, trains)
Burst recording is performed while the shutter button is pressed and held. The shutter sound
[4K Burst]
will be heard repeatedly.
1 Press the shutter button halfway
2 Press and hold the shutter button fully for as long as you want to
perform recording
●
Recording will start approximately 0.5 seconds after you press the shutter button fully. Therefore, press
the button fully as soon as possible.
●
If you are using Auto Focus, continuous AF will work while recording. Focus will be adjusted
continuously.
For capturing unpredictable photo opportunities (e.g., plants, animals, children)
Burst recording starts when the shutter button is pressed and stops when pressed again.
[4K Burst(S/S)]
Start and stop tones will be heard. "S/S" is an abbreviation of "Start/Stop".
1 Press the shutter button fully
2 Press the shutter button fully again
●
If you are using Auto Focus, continuous AF will work while recording. Focus will be adjusted
continuously.
When you press the [Fn1] button while recording, you can add a marker.
(Up to 40 markers for each recording.) When selecting and saving pictures from a 4K
burst file, you can skip to the positions where you added markers.
For recording as needed whenever a photo opportunity arises (e.g., the moment when a
ball is thrown)
[4K Pre-Burst]
Burst recording is performed for approximately 1 second before and after the moment that the
shutter button is pressed. The shutter sound will be heard only once.
1 Press the shutter button fully
●
In situations where you want to lock focus and exposure, such as when the subject is not at the
center, use [AF/AE LOCK].
■
2
To cancel the 4K Photo functions: In step , select [ ] .
●
When you perform 4K burst photo recording, a 4K burst file will be saved in the MP4 format.
●
Use a UHS Speed Class 3 card.
●
When recording, the angle of view becomes narrower.
●
Recording stops when the continuous recording time exceeds 15 minutes. When using an SDHC memory card, files are split into smaller picture files for recording and playback
if the file size exceeds 4 GB. (You can continue to record pictures without interruption.) If using an SDXC Memory Card, you can record pictures in a single file even if the size is
greater than 4 GB.
●
If the surrounding temperature is high or 4K photos are recorded continuously, [
down.
●
When [ ] ([4K Pre-Burst]) is set, the battery drains faster and the camera temperature rises. (to protect itself, the camera may switch to [
Select [ ] ([4K Pre-Burst]) only when recording.
DC-FZ80
[
] may be displayed and recording may be stopped halfway through. Wait until the camera cools
] ([4K Burst]))
To record the subject with reduced blur
Set mode dial to [
Set the shutter speed by rotating the rear dial
●
Approximate shutter speed for outdoor recording in fine weather conditions: 1/1000 seconds or faster.
●
If you increase the shutter speed, the ISO sensitivity becomes higher, which may increase the noise on the screen.
2
Selecting pictures from 4K burst file and saving
1
Select a picture with the [
●
In the case of recording with [
2 Drag the slide bar to perform rough scene selection
Shutter button
] button
3 Touch and drag the frames to select the frame you want to save as a picture
4 Touch [ ] to save the picture
●
The picture will be saved in JPEG format.
Changing a focus point after recording ([Post Focus] / [Focus Stacking])
You can record bursts of photos with the same quality as a 4K photo while automatically changing the focus point.
Press and hold
Recording is performed
Recording using [Post Focus]
●
We recommend using a tripod to perform [Focus Stacking].
1 Press [ ] button
2 Press to select [ON] and press [MENU/SET]
3
Determine the composition and press the shutter button halfway
●
Do not change the composition or the distance to subject before completion of recording.
4
Press the shutter button fully to start recording
●
When the recording progress bar disappears, recording automatically ends.
Start (First)
Stop (Second)
Recording is performed
■
To cancel [Post Focus]: Select [OFF] in step
Selecting a focus point ([Post Focus])
After recording, you can select a point on the screen to save a picture with that point
as the focus point.
Approximately 1 second
Recording is performed
1
On the playback screen, select the
image with the [
2
Touch the focus point
●
If there are no pictures with the focus on the
selected point, a red frame will be displayed, and
pictures cannot be saved.
●
To enlarge the display, touch [
You can make fine adjustments to the focus by
dragging the slide bar during enlarged display.
3 Touch [ ] to save the picture
●
The picture will be saved in JPEG format.
]
] on the playback screen, and press
3
] ([4K Pre-Burst]), proceed to the step .
2 .
Increasing the focus range ([Focus Stacking])
You can combine multiple pictures from pictures recorded using [Post Focus] to create
a single picture with an expanded focus range.
1 Touch [
([Post Focus])"
2
Choose a stacking method and touch it
] icon and press
Settings: [Auto Merging] / [Range Merging]
3
(When selecting [Range Merging])
Touch the focus point
●
Select positions at two or more points.
●
Focus points between the selected two positions
will be selected.
●
Positions that cannot be selected, or that would
produce an unnatural result will be grayed out.
].
●
Touch a position again to deselect it.
4
Touch [
●
The picture will be saved in JPEG format.
Rear dial
] on screen in step of "Selecting a focus point
2
Set/Cancel Set/Cancel
Reset Reset
] to combine and save the picture