Prior to
Function
Installation
EN
installation
check
After installing the control device, laying the high-voltage cable and attaching the stainless steel contact plates, the
setup should be retested to ensure that it functions correctly. Perform the test using a standard multimeter. Set "direct
current – 300 V" and measure the voltage between the respective stainless steel contact plate and an earthing point (e.g.
unpainted parts of the vehicle body). The value should be 250–300 V. If the function check is successful but voltage fails
to build up after installation, an installation error has occurred.
Blinking at regular intervals (approx. every 5 seconds) = OK: high voltage has built up.
Fast blinking = voltage is building up/dissipating. Caution: residual voltage!
LED off = device is switched off.
Prior to
Function
Installation
installation
check
1.
Is the operating voltage (12 V plus and minus) of the car battery also present at the unit connections?
2.
Is the engine switched off?
3.
Does the cable to terminal 15 have any voltage? (Is the ignition switched on? If so, the device will be switched off.)
4.
Have all the stainless steel contact plates been installed so that they do not touch any other live or earthed parts
(risk of short circuit)?
5.
Has the position of the stainless steel contact plates on the cable been changed, damaging the copper core?
6.
No voltage detected on the stainless steel contact plate: Has insulating material from the high-voltage cable
worked its way into the screw thread?
7.
Is the bonnet contact switch active and is this function available?
Prior to
Function
Installation
installation
check
0.5 A F
STOP&GO
STOP&GO
*Installing the bonnet contact switch
The bracket is fixed in such a way that the bonnet activates the pressure pin of the bonnet contact switch, i.e. so that the electric circuit is interrupted
when the bonnet is opened.
10
Trouble
Circuit
Warranty
shooting
diagram
Trouble
Circuit
Warranty
shooting
diagram
Trouble
Circuit
Warranty
shooting
diagram
12 V (–) earth
Bonnet contact
switch*
Function control light
12 V (+)
Terminal 15
Fuse box
Control device
Plus plate
STOP&GO
STOP&GO
STOP&GO
Prior to
Installation
installation
IMPORTANT! Terms of the warranty (please keep in a safe place)!
Our 1 PLUS High-voltage device comes with a 48-month functional warranty.
1.
Any reasonable complaints within the warranty period from the date of purchase will be remedied free of charge,
either through repair or delivery of a replacement product at our discretion. In order for the warranty to apply,
our product must have been properly installed and maintained in accordance with our installation instructions.
2.
To enable us respond to problems, please return the complete unit, including the cable, stainless steel contact
plates, bonnet contact switch and installation invoice, initially at your own expense.
3.
Installation and removal costs will only be covered by us in the event that the device is proven to be defective.
Any claim under Section 5 of our General Terms and Conditions shall remain unaffected, subject to the condi-
tions set out therein.
4.
Any damage caused by improper installation or incorrect, negligent or forceful operation shall invalidate the
warranty. There shall be no liability for consequential damage.
Technical changes and errors excepted.
Please fill in to claim against the warranty: For warranty claims to be processed, you must send us the filled in coupon
and the garage/installation invoice!
Garage stamp
Date of purchase
(5)
Technical support hotline
+49 (0) 7631 9727-80
Development and Sales
Norbert Schaub GmbH
Robert-Koch-Strasse 20
79395 Neuenburg am Rhein
GERMANY
Tel. +49 (0) 7631 9727- 0
Fax +49 (0) 7631 9727-27
service@stop-go.de
www.stop-go.de/en
Function
Trouble
Circuit
Warranty
check
shooting
diagram
Unit serial number
EN
11