Rapid BTX530 Instrucciones De Operación página 8

Type, Voltage
Capacity
Charging time
Shots per charge, max
Stapling speed, max continuous
Charger
Input
Output
Current
NOISE EMISSION
A-weighted sound pressure level LpA=79.3 dB(A), uncertainty K=3 dB(A)
A-weighted sound power level LwA=90.3 dB(A), uncertainty K=3 dB(A)
Recommendation for the operator to wear hearing protection.
VIBRATION
Vibration total value=1.214 m/s2 , uncertainty K=1.5 m/s2
The declared vibration total value has been measured in accordance with a standard test method and
may be used for comparing one tool with another.
The declared vibration total value may also be used in a preliminary assessment of exposure.
WARNING
The vibration emission during actual use of the power tool can differ from the declared total
value depending on the ways in which the tool is used.
It's needed to identify safety measures to protect the operator that are based on an estimation
of exposure in the actual conditions of use (taking account of all parts of the operating cycle
such as the times when the tool is switched off and when it is running idle in addition to the trigger
time).
DEFINITIONS (Figure 1, 2 and 10)
: Power adjustment knob
: Unlocking buttons
: Rail
: Charging point
REMOVAL AND CONNECTION OF THE BATTERY
1. To remove the battery
(Figure 3).
2. To connect the battery; slide it in the other direction until the connection clicks (Figure 4).
LOAD STAPLES/BRADS INTO THE MAGAZINE
1. Press the magazine latch
2. Slide the rail backwards.
3. Insert staples/brads strip as shown in figure 8 and 9.
4. Close the magazine by pushing the rail frontward until locking.
REMOVE STAPLES/BRADS FROM THE MAGAZINE
1. Press the magazine latch
2. Slide the rail backwards.
3. Remove the staples/brads from the magazine.
4. Close the magazine.
STAPLING/NAILING
1. Make sure the tool is in good working condition.
2. Turn the power adjustment knob to adjust the penetration depth of staples/brads to your need
(Figure 5).
3. Firmly press the safety yoke
6).
4. Briefly press the trigger
5. Trigger is locked as long as you do not press safety yoke against the work piece, thus preventing
accidental operation.
OPERATING INSTRUCTIONS OF CHARGER
Do not use the tool whilst charging process.
1. Remove the battery out of the tool.
2. Connect the charging point
3. Connect the charger
(Figure 10).
4. When the battery is fully charged, the LED
5. Disconnect the plug
Charge only at ambient temperature between 10°C and 50°C.
During the process of charging, the charger can become warm: this is normal.
Do not store the battery in locations where the temperature may exceed 50°C.
NOTE: For better performance press the tool against the work piece.
NOTE: In case of a jammed staple or brad, read the maintenance section. DO NOT re-fire the tool
in order to clear the jam as this may damage the tool.
ASSEMBLY
: Trigger
: Safety yoke
: Magazine
: Charger
, press the unlocking buttons
to unlock it from the tacker body.
to unlock it from the tacker body.
OPERATION
against the work piece until it is pushed in a few millimeters (Figure
and then release again (Figure 7).
of the charger into the socket
to the mains. → The LED
out of the socket and unplug the charger
100-240V, 50-60Hz
and slide the battery out of the machine
of the battery (Figure 10).
on the charger will turn red during the charge
of the charger will turn green (Figure 10).
8
Li-Ion, 7.2 V
1300 mAh
90 minutes
≈ 1500 shots
20 shots/minute
8.4V DC
1000 mA
: Battery pack
: Magazine latch
: Socket
: LED
from the mains.