Stiga MCS 470 Li D48 Serie Manual De Instrucciones página 29

3. The display does not
start and the machine
emits a sound when
pressing the power but-
ton (type "II"/"III" handle
- Advanced Series).
4. The engine is run-
ning but the cutting
means does not rotate
(type "I" handle).
5. The motor shuts down
whilst working.
6. The engine stops dur-
ing operation and the
machine emits a sound
(type "I" handle).
7. The display shows
ER3 (Fig.36.B) (type
"II"/"III" handle - Ad-
vanced Series).
8. The display alter-
nates between: ER1 +
OPC (Fig.36.B) (type
"II"/"III" handle - Ad-
vanced Series).
9. The display shows
ER1 (Fig.36.B) (type
"II"/"III" handle - Ad-
vanced Series).
10. The display alternates
between: 100% +
ER3 (Fig.36.B) (type
"II"/"III" handle - Ad-
vanced Series).
11. The display shows
ER2 (Fig.36.B) (type
"II"/"III" handle - Ad-
vanced Series).
Internal motor anomaly.
The cutting means fittings are loose.
Battery is not inserted correctly.
Low battery.
Obstructions that prevent
rotation of the cutting means.
The thermal protection has tripped
due to overheating of the motor.
Thermal protection has tripped due to
excessive current absorption caused by:
• Excessively high grass cutting.
• Obstructions that prevent
rotation of the cutting means.
• Too much grass debris
accumulated inside the chassis
and discharge chute.
The thermal protection has tripped
due to overheating of the motor.
Thermal protection has tripped due to
excessive current absorption caused by:
• Excessively high grass cutting.
• Obstructions that prevent
rotation of the cutting means.
• Too much grass debris
accumulated inside the chassis
and discharge chute.
Drive motor over current for heavy
working conditions (drive under stress).
Anomaly in the electrical
connection of battery and motor.
Cutting means blocked.
Remove the safety key and contact your
Dealer or the Authorised Service Centre
for checks, replacements or repairs.
Immediately turn off the motor
and remove the safety key.
Contact the Authorised Service Centre for
checks, replacements or repairs (par. 8.1).
Open the hatch and check that the battery
is fitted in its housing correctly (par. 7.2.4).
Check the battery status and recharge
if necessary (par. 7.2.3).
Remove the safety key, wear work gloves and
remove grass or debris from the lower part of
the machine and/or from the discharge chute.
Wait for at least 5 minutes and
restart the machine.
• Set a higher cutting height when the
grass is very tall, then set a lower height
and cut the lawn again (par. 6.4.1).
• Remove the obstructions (par. 7.3.2).
• Clean the machine (par. 7.3.1)
Wait for at least 5 minutes and
restart the machine.
Wait for at least 5 minutes and
restart the machine.
• Set a higher cutting height when the
grass is very tall, then set a lower height
and cut the lawn again (par. 6.4.1).
• Remove the obstructions (par. 7.3.2).
• Clean the machine (par. 7.3.1)
Wait for at least 5 minutes and
restart the machine.
– Make sure that the wheels are not
blocked. Clean as needed.
– Check the slope of the land you
are working on (par. 6.4.1).
–
Remove the safety key and contact your
Dealer or the Authorised Service Centre
for checks, replacements or repairs.
Turn the machine off, remove the
safety key and wear work gloves.
Check and eventually remove any obstructions
in the machine lower side (par. 7.3.2) that
prevent rotation of the cutting means.
If the problem continues, contact the
Authorised Service Centre for checks,
replacements or repairs (par. 8.1).
EN - 14