General Safety; Electrical Safety - Water Ace R100U Manual Del Usuario

READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of
the following signal words and be alert to the potential for
personal injury.
warns about hazards that
injury, death or major property damage if ignored.
warns about hazards that can cause serious per-
sonal injury, death or major property damage if ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which are
important but not related to hazards.
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition.
Replace missing or damaged safety labels.

GENERAL SAFETY

1. To avoid risk of serious bodily injury and property damage,
read the safety instructions carefully before installing this
pump.
2. Follow local and/or national plumbing and electrical
codes when installing the pump.
3. Hazardous Pressure. The pump body may
explode if used as a booster pump unless a relief valve
capable of passing the full pump flow at 60 PSI (414
kPa) is installed. Never run the pump dry. To do so can
damage internal parts, overheat pump (which can cause
burns to people handling or servicing pump), and will void
warranty!
4. Risk of fire or explosion. To avoid risk of
fire and explosion, Pump Water Only with this pump. Do
not use this pump in an atmosphere that might contain
flammable fumes or vapors.
5. Burn Hazard. If water is trapped in the
pump during operation it may turn to steam. Trapped
steam can lead to explosion and burns. Never run the
pump with the outlet closed or obstructed.
WA-253P7560
will
cause serious personal
WARNING
Hazardous pressure!
Install pressure relief
valve in discharge pipe.
Release all pressure on
system before working on
any component.
6. If used with a well for potable water, always disinfect the
well and test the water for purity before using. Check with
your local health department for testing procedures.
7. Complete pump and piping must be protected against
freezing. Freezing will cause damage and void the warranty.
8. This pump is not designed, nor intended, for the pumping
of chemicals or corrosive liquids. Pump water only with
this pump.
9. Do not run pump dry. If the pump is dry, damage will
result and void the warranty.

ELECTRICAL SAFETY

The pump is supplied with a 3-conductor grounding
type cord. Connect only to a properly grounded, GFCI
protected outlet. Do not lift the pump by the electrical cord.
Match the motor voltage and the power supply volt-
age. The supply voltage must be within +/- 10% of the
motor nameplate voltage. Incorrect voltage can cause fire or
seriously damage the motor and will void the warranty. If in
doubt, consult a licensed electrician.
The pump is non-submersible. Keep the motor dry at
all times. Do not wash the motor. Do not immerse.
Protect the motor from wet weather.
If using an extension cord, use only a UL approved
indoor/outdoor, 3-wire, grounding type cord. Do not
allow any part of the cord or the receptacle ends to sit in
water or in damp locations.
Unplug the pump before servicing. To avoid fatal
shocks, proceed as follows if the pump needs
servicing.
WARNING
Hazardous voltage. Can
shock, burn, or cause death.
Ground pump before connecting
to power supply. Disconnect
power before working on pump,
motor or tank.
electrical shocks, DO NOT stand in water or put your finger
in the fuse socket.
C. Ground the pressure switch or motor before before running
this pump.
D. Plug pump into a Ground Fault Circuit Interrupter (GFCI)
protected grounded outlet only.
2
A.Disconnect the power to
the pump outlet box
before pulling the pump
plug. Modern motors are
designed to operate at
high temperatures.
To avoid burns when
servicing pump, allow it
to cool for 20 minutes
after shut-down before
handling.
B. Take extreme care when
changing fuses. To reduce
the chance of fatal