4
INSTALLATION
For your and other people safety, follow the "Safety
Regulations" in section 3 carefully.
4.1 Packaging
The original packaging has been designed to protect the ma-
chine during transport. We recommend keeping the packaging
for future transport.
4.2 Installation Instructions
Before installing the machine, read the following safety in-
structions carefully.
• Put the machine in a safe place.
• Make sure children cannot play with the machine.
• Do not place the machine on hot surfaces or near open
fl ames.
The coff ee machine is now ready to be connected to the power
supply.
Note: It is recommended to wash the compo-
nents before using them for the fi rst time and/
or after they have not been used for a certain period of
time.
4.3 Machine Connection
Electric power can be dangerous! It is therefore
essential to follow the safety regulations care-
fully. Do not use faulty cords! Faulty cords and plugs
must be immediately replaced by authorized service
centres.
Appliance voltage has been pre-set by the manufacturer. Make
sure that the power voltage matches the indications on the
identifi cation plate on the bottom of the appliance.
• Make sure that the ON/OFF button (2) is not pressed before
connecting the machine to the power supply.
• Fit the plug into a wall socket with suitable power voltage.
4.4 Water Tank
• (Fig.1) - Remove the water tank (3).
• (Fig.2) - Rinse the water tank and fi ll it with fresh drinking
water taking care not to overfi ll it.
• (Fig.1) - Insert the water tank making sure that it has prop-
erly been replaced in its former seat.
Use only fresh, non-sparkling drinking water to
fi ll the tank. Hot water, as well as any other liq-
uid, may damage the tank. Do not turn on the machine
with empty water tank: make sure there is enough wa-
ter in the tank.
• 16 •
4.5 Circuit Priming
In the beginning, after dispensing steam or when the water
tank is empty, the machine's water circuit must be primed.
• (Fig.3) - Press the ON/OFF button (2).
• (Fig.4) - Place a container under the steam spout.
• (Fig.5) - Open the "hot water/steam" knob (4) by turning it
anticlockwise.
• (Fig.6) - Switch the selection knob to the "
(17).
• Wait until a steady jet of water fl ows out of the steam spout
(Pannarello).
• (Fig.6) - Switch the selection knob to the " "position
(17).
• Close the "hot water/steam" knob (4) by turning it clock-
wise. Remove the container.
4.6 Using the machine for the fi rst time
or after a period of inactivity
This simple operation ensures an optimum brewing and must
be performed:
- at fi rst start-up;
- when the machine remains inactive for a long time (more
than 2 weeks).
Dispensed water must be emptied into an ad-
equate drain. It is not suitable for food use. If
the container fi lls up, stop dispensing water during the
cycle and empty it before resuming the operation.
• (Fig.2) - Rinse the tank and fi ll it again with fresh drinking
water.
• (Fig.4) - Place a container under the steam wand (Pannarel-
lo). Open the knob (4) by turning it counter-clockwise and
switch the selection knob (17) to the "
• Dispense the whole water tank from the steam/hot water
wand. To end the operation, switch the selection knob (17)
to the " " position and close the knob (4) by turning it
clockwise.
• (Fig. 2) - Fill the water tank with fresh drinking water.
• (Fig.11-12) - Insert the portafi lter into the brew unit from
the bottom (6) and turn it from left to right until it locks into
place.
• (Fig.13) - Place a suitable container under the portafi lter.
• Turn the selection knob (17) to the "
pense all the water in the water tank. Once the tank is empty,
stop dispensing and switch the selection knob (17) to the "
" position.
• Fill the tank again and wait until the "machine ready" light
(15) turns on.
• (Fig.16) - Remove the portafi lter from the unit by turning it
from right to left and rinse it with fresh drinking water.
The machine is now ready; please see related sections for oper-
ating details on how to brew coff ee and dispense steam.
" position
" position.
" position and dis-