Safety Instructions - wolfcraft 5018000 Instrucciones De Aplicación

This cutting stand is an aid for cutting work (exclusively for metal)
with a one-hand angle grinder. It is suitable for use with most
angle grinders with a disc size of Ø 180 or Ø 230 mm. Carefully
read this instruction manual and especially the safety instructions
before using the cutting stand.
Assembly Instructions
Refer to illustration (A) and the detailed photos (B - I) when
assembling the stand.
You require the following for the assembly work: open-jawed
spanners (SW 10, SW 13, SW 17, SW 21), Allen key (2.5 mm and
a slotted screwdriver (6 mm).
• Fix the swivel arm (2) to the base plate (1) using the M8
hexagon bolts (3), the washers (4), the tooth lock washers (5)
and the hexagon nuts (6).
• Screw both of the adjusting screws (7) into the threaded
boreholes in the swivel arm.
• Now fix the rear jaw (8) to the base plate with the M10 hexa-
gon bolt (11) und the square nut (12). Then mount the M10
hexagon bolt (9), locking washer (10) and the square nut (12)
for the angle adjustment with the jaw and the base plate.
• Fix the front moving clamping jaw (13) with the washer (14),
tappet (15), hexagon bolt (11) and square nut (12) to the base
plate; only tighten the hexagon bolt to such an extent that the
clamping jaw still has a small amount of free motion. Then
screw the handle (16) into the tappet. Place the locking plate
(17) over the head of the hexagon bolt and mount it in the
threaded borehole of the tappet using the M8 hexagon bolt
(18). By rotating the tappet at the handle, ensure that the
clamping jaw can be tightened, loosened and moved along the
ground plate. The free motion of the clamping jaw is adjusted
with the hexagon bolt (11). Now adhere both of the material
protectors (19/20) to the clamping jaws.
• Mount the protective cover (22) with the two rubber washers
(23) and the end cap (24) onto the protection hood hoop (21).
If it should not be possible to push the end cap on, use a
hammer. Then insert the protection hood hoop through the
boreholes in the swivel arm and secure it with the threaded
screw (25).
• Mounting the angle grinder.
Align the angle grinder in the swivel arm between the two
boreholes. Fix the angle grinder in position with two matching
threaded rods (26 or 27). Align the angle grinder with both of
the adjusting screws (7) perpendicular to the base plate.
Tighten both of the hexagon nuts (28) over the threaded rods.
Then tighten the handle (29). Check the free running of the
cutting disc in the cutting gap. Align the swivel arm with the
mounted angle grinder using the three fastening screws (3)
if required.
• After completing the assembly, switch the angle grinder
on for a few seconds and then switch it off again.
Re-check the tightness of all of the screws and the
screwed connections.
• Your cutting stand is now ready for use.
t

Safety instructions

• It is imperative that you adhere to the information in the
instruction manual for the angle grinder used. This device must
correspond to the VDE standards. Only devices with a CE
symbol are to be used.
• Keep children away from the workplace and also keep the tools
out of the reach of children.
• Always wear protective goggles, ear protection, protective
gloves and a mouth or nose protection respectively.
• Wear suitable working clothes; do not wear any wide clothing
or jewellery as they could be caught up in moving parts.
Non-slip shoes are recommended. Wear a hair net if you have
long hair.
• Before use, ensure that the device is correctly and securely
mounted in the retainer.
• Never stop the cutting disc with the hands or other objects.
Never reach into the working area of the running cutting disc or
touch the cutting disc during the work. There is a risk of injury!
• Fix the cutting stand on both of the mounting perforations to
the base plate (1) on the workbench. Ensure that the bench
and the stand are securely positioned.
• Ensure that the workplace is clean and well illuminated.
• Always use the protective cover (22).
• Only use the cutting stand with an angle grinder which is
equipped with the suitable metal protective cover around the
cutting disc.
• Position this protective cover so that the cutting disc runs freely
in the open part and so that the protective cap is unable to
make contact with the work piece.
• Cutting work generates sparks. Ensure that no flammable
materials are in the working area. Sparks can damage paint,
glass and other surfaces. Do not wear any nylon or polyester
clothing, but suitable non-flammable work clothes.
• Ensure that the mains cable does not protrude into the working
area of the disc or where sparks are flying.
• Ensure that the work piece is correctly fixed in position between
the two clamping jaws and is firmly positioned on the base
plate.
• Do not use work pieces which are too large to be fixed in
position between the two clamping jaws.
• Clamp the work piece so that it is stress-free.
• Secure the cut-off material in order to avoid injuries resulting
from flying or falling work pieces.
• Ensure that the cutting disc is not tilted and that it is always
sufficiently tightened.
• Do not remove the work piece when the disc is rotating.
• Ensure that it is not used together with liquids.
• Regularly inspect the firm seating of all of the screws before
and during use as they can become loose due to vibration.
• Store the cutting stand in a dust-free and dry place.
• Regularly inspect both the stand and the cutting disc for any
damage. Under no circumstances should you use a disc if
you should determine any dents, notches or other forms of
damage. The stand is also not to be used if you detect any
damage.
• Ensure that the cutting disc of your angle grinder is mounted
perpendicular to the base plate.
• Only use cutting discs and no roughing discs.
• Always observe the cutting depths as there is otherwise the risk
of damaging your workbench.
• Always use the lever (29) of the cutting stand to bring the
machine into the end position.
• Always remove the plug of your angle grinder from the socket
when not in use, changing the disc and when completing all
cleaning and adjustment work.
• All liability and warranty claims will be excluded in the case of
the use of non-permitted drive devices and the making of all
technical modifications to the cutting stand.
5