Virutex FR129 VB Manual De Instrucciones página 4

At the opposite end of tube K (Fig. 3), place reference
stop M (Fig. 3) in the corresponding drill hole for the
length of hinge to be fitted, or in the nearest if it does
not correspond with that of those marked.
7. PLACING HINGES WITHOUT TEMPLATE ON
RIGHT HAND DOOR
7.1 PLACING HINGES ON THE FRAME
Ensure that the operations of fitting or adjusting the bit,
the template and the distribution tube indicated in section
6 have been fully carried out before proceeding.
ADJUSTING THE RECESS HEIGHT
The machine has stop ruler M (Fig. 15 and 7), with two
scales marked from the centre towards the two ends,
one for each bit diameter, ½ " or 1
Place the two stops A1 (Fig. 15 y 7) here in the position
corresponding to the height (3 ", 3
") of the hinge we are about to fit.
½
POSITIONING THE MACHINE FOR THE FIRST RECESS
Loosen levers S (Fig. 9). Place the machine (Fig. 9) over the
rebate of the frame, turning the indicator "RIGHT FRAME"
MD (Fig. 9 and 5) towards the upper part of it.
Move the machine sideways to the end of the frame rebate
and upwards until support H (Fig. 9) touches the bottom
of the rebate in the crossbeam of the frame.
Tighten the clamp vises over the thick part of the door-
frame by means of crank handles F (Fig. 9).
Move machine base 2 (Fig. 9) along the width of the re-
bate until it reaches interior face T (Fig. 9) of the rebate
on the frame. Secure the machine in this position using
levers S (Fig. 9).
ADJUSTING THE WIDTH OF THE RECESS
The width of the recess is obtained by regulating stop bolt
B1 (Fig. 16). Follow these steps:
Ensure that the machine has been disconnected from
the mains.
Hold the bit so that it touches the edge of the frame with
cutting edge Q (Fig. 15). Lock it into this position with
knob U (Fig. 16). Place stop bolt B1 at distance X (Fig. 16)
of fixed stop B2 (Fig. 16), equal to the width of the recess
you wish to make. The width stop will now be adjusted.
AJUSTING THE DEPTH OF THE RECESS
Push the motor body towards the frame until the bit tip
is touching the wood. Lock it into this position with knob
U (Fig. 9).
Place the hinge between head V and nut W (Fig. 10). Adjust
the width of the hinge with this bolt.
Remove the hinge and release knob U (Fig. 9).
STARTING UP THE MACHINE
To start the machine, press button X forward (Fig. 8) to the
on position. To stop the machine, simply press the back of
the switch and it will return to the off position.
ROUTING THE FIRST RECESS
4
¼ " (Fig. 15 and 7).
½ ", 4 ", 4 ½ ", 5 " or 5
By gradually pushing motor body 1 (Fig. 9), the bit will
make an incision on the frame to the depth of the pre-
viously adjusted hinge. Secure the machine at this depth
with knob U (Fig. 9).
Next, move the motor body lengthways and sideways,
between the adjusted stops until obtaining a recess for
the whole shape of the hinge. Once the recess for the first
hinge has been obtained, stop the machine. Loosen crank
handles F (Fig. 9), slide the machine to the approximate
position for the second hinge and once again secure crank
handles F.
FITTING THE DISTRIBUTOR TUBE
Slightly loosen upper crank handle FS (Fig. 11) and separate
the machine from the frame on this side by approxima-
tely 13/64"=0.5 cm to facilitate the fitting of previously
prepared distributor tube K (Fig. 11).
Fit distributor tube K (Fig. 11) to support H (Fig. 11 and
5). To do this, pull pin G1 (Fig. 5) until connector I (Fig. 5)
of distributor tube K (Fig. 11) can enter between supports
H (Fig. 11 and 5). Release it when drill coincides with pin
G1 (Fig. 5) to bring about the locking.
ROUTING THE SECOND AND THIRD RECESSES
To position the machine for the second recess, loosen both
crank handles F (Fig. 11), place centring device M (Fig. 11)
of hinge distributor tube K (Fig. 11) on the bottom part
of the recess of the first hinge and, leaning the machine
against the recess, secure crank handles F (Fig. 11) once
again in this position.
Rout the second hinge recess in the same way as explained
for the first. This process is repeated to rout the third recess,
positioning distributor tube K (Fig. 11) over the second
hinge. This operation is repeated for the fourth if working
with distributor tube 5 (Fig. 2) for four hinges.
7.2 PLACING THE HINGES ON THE DOOR
FITTING THE DISTRIBUTOR TUBE
Fit hinge distribution tube K (Fig. 13) with stop J (Fig. 13)
facing downwards, into support G (Fig. 13) on the side
of the support marked "RIGHT HAND DOOR" MI (Fig. 13).
Secure it with pin G1 (Fig. 13).
MACHINE POSITION FOR THE FIRST RECESS
Loosen levers S (Fig. 13) and position the machine on the
edge of the door, with tube K (Fig. 13) towards the upper
side of it.
Move the machine along the edge of the door until stop
J (Fig. 13) touches the upper end of it. Tighten the clamp
vises to the door using crank handles F (Fig. 13). Move base
2 of the machine (Fig. 12 and 13) until stops Y (Fig. 12) on
either side of the base touch the heads of screws Z (Fig.
12). Secure levers S (Fig. 13) once again in this position.
The position of screws Z (Fig. 12) with respect to stops Y
(Fig. 12) provide a 1/16"=1.5 mm space in the hung door
between the entrance face of the door and the interior
side of the rebate. If less space is required, screws Z can be