Virutex FR129 VB Manual De Instrucciones página 6

has to be adjusted with respect to the frame with screws
C1 (Fig. 17). Secure them with bolts D1 (Fig. 17), and secure
the base in this position with levers S (Fig. 17).
Once adjusted for the frame, adjustable stops C1 (Fig. 17
and 18) can also be used to position the machine in the
door, but, unlike the standard process (Fig. 18), using the
exit side.
11. RECOMMENDATIONS
Use the templates which correspond to the shapes and
sizes of the hinges to be placed.
Use suitable bits and the corresponding template guides
for the diameter of the bit.
12. MAINTENANCE
12.1 BRUSHES AND COLLECTOR
Unplug the machine from the mains before
carrying out any maintenance operations.
Remove the screws E1 (Fig. 19) that hold the side covers
G1 and detach them.
Remove the brush-holder J1 (Fig. 20) with small screw-
driver K1, using one of the brush-holder side tabs to lever
it out.
Push back the end of spring F1. Keep it in this position to
extract the brush and replace it with a new genuine VIRUTEX
brush. Reinsert the brush-holder, ensuring that it is firmly
positioned in the casing and that each of the brushes exerts
a small amount of pressure on the collector.
Re-attach the covers G1 with the corresponding screws,
making sure that no wires get caught in the process.
It is advisable to leave the machine running for 15 minutes
once the brushes have been changed.
If the collector burns or juts out, it should be serviced by
a VIRUTEX service technician.
To ensure that mobile parts continue to move correctly,
remember to get rid of any dirt, dust and shavings pro-
duced when making recesses.
Keep the cable and plug in good service condition.
13. ACCESSORIES
Standard templates for different hinges
Template guides for different bit diameters.
2945471 - 90º CORNER CHISEL RC29M
1222024 - CHUCK COLLET Ø 8 mm
14. TEMPLATE GUIDES AND CORRESPONDING
BITS
See (Fig. 21)
15. NOISE LEVEL
These levels have been measured according to the European
Standard EN50144.
6
The noise level in the workplace could go over 85dB(A).
In this case it is necessary for the user to wear noise
protection.
16. GUARANTEE
All of VIRUTEX portable tools are guaranteed for 12 months
from the date of supply, excluding any damage which is
a result of incorrect use or of natural wear and tear on
the machine.
All repairs should be carried out by the official VIRUTEX
technical assistance service.
VIRUTEX reserves the right to modify its products without
prior notice.
E S P A Ñ O L
FRESADORA DE HERRAJES FR129 VB
Nota importante
Lea atentamente el FOLLETO DE INSTRUCCIO-
NES GENERALES DE SEGURIDAD que se ad-
junta con la documentación de la máquina.
Conserve los dos manuales de instrucciones
para posibles consultas posteriores.
Nota importante
Lea atentamente el FOLLETO DE INSTRUCCIO-
NES GENERALES DE SEGURIDAD que se ad-
junta con la documentación de la máquina.
1. Asegúrese antes de enchufar la máquina, que la tensión
de alimentación se corresponda con la indicada en la chapa
de características.
2. Mantenga siempre las manos alejadas del área de corte.
Sujete siempre con la seguridad la máquina.
3. Use siempre herramientas originales VIRUTEX. No use
nunca herramientas defectuosas o en mal estado.
4. Utilizar siempre fresas con el diámetro de la caña ade-
cuado a la pinza a utilizar y adaptadas a la velocidad de
la herramienta.
Desconectar la máquina de la red eléctrica
antes de proceder a cualquier operación de
mantenimiento.
1. CARACTERÍSTICAS
Potencia.......................................................750 W
Velocidad en vacío...........................................30.000/min
Nivel de presión acústica continuo
equivalente ponderado..............................85 db (A)