Product Safety Information - Ingersoll Rand QM3 Serie Especificaciones Del Producto

EN

Product Safety Information

Intended Use:
These fixtured electric tools are designed for threaded joint fastening applications.
When operated continually for long periods of time, Nutrunners may become hot at the spindle end of the
•
tool. Take all precautions necessary to avoid skin contact with the hot surfaces. Prolonged contact may result
in burns.
For additional information refer to Fixtured Electric Angle Wrench, Screwdriver or Nut Runner used with a Controller Product Safety
Information Manual Form 16573693.
Manuals can be downloaded from www.ingersollrandproducts.com
Declaration of Noise Emission
Model
QM9Z{ }
All other models
■ Values determined according to noise test code ISO 15744.
Lubrication
All lubrication should be made only by authorized trained personnel; when such service is required for these tools (at each 250,000 cycles)
contact the nearest Ingersoll Rand Authorized Service Center.
Installation
Power Supply:
For QM9 and QM7 models, AC220 Volts is recommended.
Cable Connection:
Before attaching or removing cables, to or from, the 90° Strain Reliefs, unscrew the 90° fitting: allowing cable to rotate freely inside Strain Relief.
Electronics Pod Flange:
For Memory Chip access, flange on Electronics Pod can be oriented in one of two positions: each 90° from one another. Electronics Pod must be
electrically connected to earth ground through the Pod Flange.
Locked Spindle Option:
For tools with Locked Spindle option, the Output Spindle may be locked fully retracted or fully extended. Disassembly of the Spindle Assembly
is required to change configuration. Refer Maintenance Information manuals at www.ingersollrandproducts.com for detailed instructions.
Mounting Options:
There are two options for mounting tools.
1) When fixture is between Spindle and Transducer (Y), remove and discard Spacer Plate (Z).
Note: Fixture Plate (X) must maintain thickness of Spacer Plate (Z).
2) When Fixture Plate (X) is in front of Spindle Flange, Spacer Plate (Z) thickness may be ignored:
Note: M8 or M10 mounting screws must be lengthened by Fixture Plate (X) thickness.
Recommended Fixture Plate Dimensions:
Plate
Thickness
Series
(mm)
QM3 10
QM5 11.2
QM7 11.2
QM9 18
* QM9 18
Electronics Pod N/A
* For QM9S{ } 25C/20C/18C/15C { }
Note: For Offset tools refer to engineering drawings 80155815, 80156037 and 80224009.
EN-1
■ Sound Pressure Level, L
X
Minimum Bolt
Counter-bore Ø Circle Ø
(mm) (mm)
59 45
67 50
71 57.16
90 76.2
123 100
N/A 60
pA
< 71 dB(A)
< 70 dB(A)
Y
X
Bolt Hole Ø
Number of
Bolt Holes
(mm)
2 8.97 - 8.71 M8 x 1.25 x 30 31.015 - 30.985
2 10.63 - 10.37 M10 x 1.5 x 35 32.515 - 32.485
6 8.97 - 8.71 M8 x 1.25 x 30
6 8.97 - 8.71 M8 x 1.25 x 45
10 10.33 - 10.13 M10 x 1.5 x 45 82.095 - 82.065
2 6.65 - 6.05
Uncertainty, K
3 dB(A)
3 dB(A)
Z
Y
Through
Supplied
Hole Ø
Bolt Size
(mm)
44.48 - 44.45
63.53 - 63.5
M6 x 1 x 18 39.0 - 50.0
pA
Through Hole
ID Chamfer
0.5 x 45°
1.05 x 45°
1.05 x 45°
1.55 x 45°
1.55 x 45°
N/A
04581278_ed8