Electrical Supply; Wiring Requirements; Connecting To 120V/208V Circuit - Fulgor Milano F1SP24 1 Serie Instrucciones De Installación

ELECTRICAL SUPPLY

Before installing the oven have a qualified electrician
verify that your home is provided with adequate
electrical service and that the addition of the oven will
not overload the branch circuit on which it is to be
installed.
A separate three-wire or four-wire single phase,
120V/240V, 60 Hz, or a 120V/208V, 60Hz branch
circuit is required.
NOTE : FOR USE WITH 120V/208V, 60 HZ SUPPLY
Location of rating plate
VOLTAGE, SEE CONNECTING TO 208V CIRCUIT.
For hook-up of the oven you will need to have an
approved junction box installed where it will be easily
reached through the front of the cabinet where the
oven will be located. The oven has 3 feet of conduit.
Allow two to three feet of slack in the line so that the
oven can be moved if servicing is ever necessary.
DO NOT shorten the flexible conduit.

WIRING REQUIREMENTS

Location of rating plate
When making the wire connections, use the entire
length of the conduit provided (3 feet). The conduit
must not be cut.
Before making connections make sure the power is off
and read and observe the following:
1. A separate three-wire or four-wire, single phase,
120V/240V, 60 Hz or 120V/208V, 60 Hz branch
circuit is required for the oven.
. 2 The oven must be connected with Copper or
WIRING REQUIREMENTS
Aluminum wire.
3. In the United States:
When making the wire connections, use the entire
Wiring must conform to the National Electrical
length of the conduit provided (3 feet). The conduit
Code, ANSI/NFPA No. 7 latest edition. You can
must not be cut.
obtain a copy of the National Electrical Code by
Before making connections make sure the power is off
writing to: National Fire Protection Association
and read and observe the following:
Batterymarch Park Quincy, MA 02269
1. A separate three-wire or four-wire, single phase,
In Canada:
120V/240V, 60 Hz or 120V/208V, 60 Hz branch
Wiring must conform to Canadian Electrical Code
circuit is required for the oven.
C22.1- latest edition. You can obtain a copy of the
. 2
The oven must be connected with Copper or
Canadian Electrical Code by writing to: Canadian
Aluminum wire.
Standards Association 178 Rexdale Boulevard
3. In the United States:
Rexdale (Toronto), Ontario, Canada M9W 1R3
Wiring must conform to the National Electrical
4. Wire size (Copper or Aluminum wire) and
Code, ANSI/NFPA No. 7 latest edition. You can
connections must be suitable for the rating of the
obtain a copy of the National Electrical Code by
appliance as per the National Electrical Code
writing to: National Fire Protection Association
requirements. The flexible armoured cable
Batterymarch Park Quincy, MA 02269
extending from the oven should be connected
In Canada:
directly to the junction box.
Wiring must conform to Canadian Electrical Code
5. The junction box should be located so as to allow
C22.1- latest edition. You can obtain a copy of the
as much slack as possible between the junction
Canadian Electrical Code by writing to: Canadian
box and the oven so it can be moved if servicing is
Standards Association 178 Rexdale Boulevard
ever required.
Rexdale (Toronto), Ontario, Canada M9W 1R3
6. A U.L. listed conduit connector must be provided
4. Wire size (Copper or Aluminum wire) and
at each end of the power supply cable.
connections must be suitable for the rating of the
appliance as per the National Electrical Code
requirements. The flexible armoured cable
extending from the oven should be connected
directly to the junction box.
5. The junction box should be located so as to allow
as much slack as possible between the junction
box and the oven so it can be moved if servicing is
ever required.
6. A U.L. listed conduit connector must be provided
at each end of the power supply cable.
to power source, and using the following sequence:

CONNECTING TO 120V/208V CIRCUIT

This option is provided for areas where standard 240V service is
not available. This option must be accessed with the oven connected
to power source, and using the following sequence:
1. Befor installing the oven remove the upper frontal cover.
2. Connect the 208V Jumper provided into the female connector as
showed below.
3. Reassemble the upper cover, than connect the product to the power
supply and check all functions.
The voltage setting is stored and kept even after a long power-off.
ELECTRICAL SHOCK HAZARD
The electrical power to the oven branch circuit must be shut off
while line connections are being made.
Do not use an extension cord with this appliance.
Electrical ground is required on this appliance. The free end of the
green wire (the ground wire) must be connected to a suitable
ground. This wire must remain grounded to the oven.
The voltage setting is stored and kept even after a long power-off.
If cold water pipe is interrupted by plastic, non metallic gaskets,
union connections or other insulating materials, DO NOT use for
grounding.
DO NOT ground to a gas pipe.
ELECTRICAL SHOCK HAZARD
DO NOT have a fuse in the NEUTRAL or GROUNDING circuit. A
The electrical power to the oven branch circuit must be shut off
fuse in the NEUTRAL or GROUNDING circuit could result in an
while line connections are being made.
electrical shock.
Do not use an extension cord with this appliance.
Check with a qualified electrician if you are in doubt as to whether
Electrical ground is required on this appliance. The free end of the
the appliance is properly grounded.
green wire (the ground wire) must be connected to a suitable
Failure to follow these instructions could result in serious injury or
ground. This wire must remain grounded to the oven.
death.
If cold water pipe is interrupted by plastic, non metallic gaskets,
union connections or other insulating materials, DO NOT use for
grounding.
DO NOT ground to a gas pipe.
DO NOT have a fuse in the NEUTRAL or GROUNDING circuit. A
Do not repair or replace any part of the appliance unless specifically
fuse in the NEUTRAL or GROUNDING circuit could result in an
recommended in the manual. All other servicing should be done by a
electrical shock.
qualified technician. This may reduce the risk of personal injury and
Check with a qualified electrician if you are in doubt as to whether
damage to the oven.
the appliance is properly grounded.
Never modify or alter the construction of the appliance by removing
Failure to follow these instructions could result in serious injury or
panels, wire covers, screws, or any other part of the product.
death.
Do not repair or replace any part of the appliance unless specifically
recommended in the manual. All other servicing should be done by a
qualified technician. This may reduce the risk of personal injury and
damage to the oven.
Never modify or alter the construction of the appliance by removing
panels, wire covers, screws, or any other part of the product.
Installation Manual
ENGLISH
WARNING
WARNING
CAUTION
CAUTION
ENGLISH
7