Fender 65 TWIN REVERB Instrucciones De Funcionamiento página 5

POWER RATING
260 WATTS
A. P O W ER RATIN G - C onnect the power line cord to a
g roun d e d A C re ce ptacle in a c corda nc e with the
voltage and frequency ratings shown on the Rear Panel
of the amplifier.
B. F U S E - Protects the amplifier from electrical faults.
Replace fuse only with same type and rating listed on
the fuse holder. If the amplifier repeatedly blows fuses,
take the amplifier to an authorized F ender Service
C enter.
C . P OW ER SWIT C H - Push U P to switch O N the amplifier.
Push DO W N to switch O F F the amplifier.
D. STA N D B Y SWIT C H - Push D O W N to put the amplifier
into STA N D B Y mode. Push U P to put the amplifier into
normal O P ERATIN G mode. In STA N D B Y mode, power
is supplied to the tube filaments only. This eliminates
w a rm-u p tim e wh e n re t u rning th e a mplifier to
FIG. 1
Replace tubes with id entical F e n d e r ® original equipment only (see SPE CIFIC ATIO N S below). Tu be location is printed on th e tube label, inside th e cabinet.
TYPE:
PART NUMBE R :
POWER REQUIREMENTS:
POWER OUTPUT:
IMPEDANCES:
FUSE TYPE:
SPEAKER COMPLEMENT:
TUBE COMPLEMENT:
FEATURES:
DIMENSIONS:
WEIGHT:
`65 Twin Reverb – Rear Panel
FUSE
Tube Adjustments
The tube B ALA N C E and BIAS of your '65 Twin Reverb is adjusted at the factory and should
provide years of service before needing attention. If the sound quality of the amp has degraded
noticeably and H U M B ALA N C E and BIAS adjustments fail to restore sound quality, the tubes
are worn and need replacement. Note that pre-amplifier tubes last longer than output tubes. If
you are not sure about the condition of your tubes or the following procedures, take your
amplifier to an authorized F ender Service C enter.
A. H U M B ALA N C E ADJU STM E NT - This adjustment minimizes the hum heard at the speakers
due to tube filament imbalance. B alance is usually adjusted only when tubes have been
replaced. • Adjustment Instructions: Turn the amplifier O N for 2 minutes with nothing
plugged into any of the IN P UTS. Rotate the VIB RAT O C H A N N EL volume, middle, and bass
knobs fully clockwise and the treble knob fully counter-clockwise.
N O RMAL C H A N N EL knobs fully counter-clockwise. Switch O F F the REVER B and VIB RAT O
effects. Then insert a slotted screwdriver into the B ALA N C E ADJU STM E NT control, (see
"A" in FIG . 1) and rotate back and forth to the position with the least amount of hum.
B . BIA S AD JU ST M E N T -
repla ce d with tu b es not ide ntic al to th e original tu bes and should be adjust ed only b y an
a uthorized F e nder S ervice C e nter.
Specifications
PR 186
021-7370-000 (100V, 50/60Hz) Japan,
021-7340-000 (230V, 50Hz) UK,
260 watts
85 watts R.M.S.
INPUTS 1: 1M ohm (both channels),
OUTPUT: 4 ohms (both speaker jacks together)
4 ampere, slow-blow, 125 volt minimum
Two 12-inch Fender vintage re-issue Special Design speakers (P/N-037617)
OUTPUT: Four Fender Special Design 6L6GC's (P/N-039214),
PRE-AMP: Four Fender Special Design 12AX7A's (P/N-013341),
Two Fender Special Design 12AT7's (P/N-023531)
Vibrato and Reverb, Tilt-back legs
HEIGHT: 19-7/8 in.
WIDTH: 26-5/32 in.
DEPTH: 10-3/8 in.
64 lbs.
Product specifications are subject to change without notice.
SPEAKER
POWER STANDBY
O P ERATIN G mode and also increases tube life span.
The P O W ER switch { C } must be O N for the STA N D B Y
switch to function.
E. M AIN S P E A K E R J A C K - Plug-in conn ection for
speakers. A speaker must always be connected at this
jack when the amplifier is O N.
F. E XTE RN A L S P E A K E R J A C K - Plug-in c onn e ction for
a n e xt ern al s p ea ker. This ja c k is wire d in p arallel with
th e MAIN SP E A K E R JA C K { E }.
imp e da nc e lo ad of 4-ohms should b e us ed to a void
da ma ge to the a mplifier.
G . F O OT SWIT C H JA C K - Plug-in conne ction for the
F O O TSWIT C H which enables O N/ O F F switching of the
VIB RAT O and REVER B effects. The VIB RAT O effect
will not function without the F O O TSWIT C H plugged in.
This adjustme nt only should be ma de if the output tu bes are
021-7300-000 (120V, 60Hz) USA,
021-7330-000 (240V, 50Hz) A u s t r a l i a .
INPUTS 2: 136k ohms (both channels)
(49.2 cm)
(63.5 cm)
(21.9 cm)
5
EXT.
SPEAKER
A total sp ea ker
Rotate ALL of the
021-7360-000 (230V, 50Hz) Euro,
(29 kg)
FOOT
PEDAL