Start-Up; Work; Grass Cutting - ST MPST 84 Li 48 V1 Manual Del Usuario

Ocultar thumbs Ver también para MPST 84 Li 48 V1:
Tabla de contenido

Publicidad

• Never mow across the face of the slope. 
Lawns on a slope have to be mowed 
moving up and down and never across 
them, in forward drive, paying attention 
to the changes of direction, making sure 
that the wheels facing the slope do not hit 
any obstacles (such as stones, branches, 
roots, etc.) which may cause the machine 
to slide sideways, tip over or lose control.
• Do not stop or start suddenly 
when going up or downhill.
• Shift to drive gear very gently paying 
particular attention to prevent the
machine from tipping up.
• Reduce speed:
• before changing direction
and during tight turns; 
• before approaching a slope, especially 
downhill, to allow safe braking distance.
• Never switch to reverse gear to decrease 
speed when going downhill: this could 
cause loss of control of the machine, 
especially on slippery ground.

7.4 START-UP

To start the machine:
1. Make sure the transmission 
is engaged (par. 6.4).
2. Sit in the operator seat.
3. Turn the key (fig. 11.A).
4. Wait for the electrical check of the 
machine to be completed, during which 
the push-button panel icons will light up.
5. Press the start push-button  (fig. 12.A).
6a. For Type I push-button panel wait 
6.
for the icon (fig. 12 F) to indicate 
the battery charge status.
6b. For Type II push-button panel, wait until the 
"Ready" icon (fig. 12.K) is lit with a fixed light. 
NOTE
At the end of the electrical check the 
headlights light up for a moment.
7.5

WORK

7.5.1 Drive and movements
When moving the machine:
1. disengage the cutting means (par. 6.5); 
2. bring the cutting-means assembly to 
the highest position (position «7»);
3. press the drive pedal to move the machine 
in the desired direction of travel and
reach the desired speed by graduating 
the pressure on the pedal itself;
4. move to the work area.
DANGER
Drive can only be engaged following the 
procedure illustrated (par. 6.3) to prevent
sudden engagement which may cause 
the vehicle to tip over and the driver to
lose control, especially on slopes.
NOTE
Reverse must be engaged when 
the machine has stopped.

7.5.2 Grass cutting

1. Bring the cutting-means assembly 
into working position (par. 6.6).
2. Engage the cutting means (par. 6.5) only on 
grass lawns; avoid engaging them on stony 
ground or when the grass is very high.
3. Start driving and cutting in the grassy 
area very gradually and with caution.
4. Regulate the travel speed and the
cutting height (par. 6.6) considering
the conditions of the lawn (the height, 
density and dampness of the grass) 
and the amount of grass collected. 
NOTICE
The travel speed decreases if the battery 
charge threshold is below 40% (par. 8.2.2).
NOTE
The appearance of the lawn will improve 
if you alternate cutting in both directions 
at the same height (fig. 19.A.B).
NOTE
To be able to drive in reverse with the cutting 
means engaged, it is necessary to press and 
hold down the cut in reverse consent push-button 
(fig. 12.C) to prevent the motor from stopping.
Disengage the cutting means and move the 
cutting-means assembly to the highest position:
• When moving between work areas.
• When driving on grass free surfaces.
• Every time it is necessary to 
overcome an obstacle.
EN - 17

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Mpst 84 li 48 v2Mps 84 li 48 v1Mps 84 li 48 v2Mpns 84 li 48 v1Mpns 84 li 48 v2Mp 84 li 48 v1 ... Mostrar todo

Tabla de contenido