Consumer Information - Moen L84762 Guia De Inicio Rapido

TRIM INSTALLATION INSTRUCTIONS cont.
5
1
2
4
3
6
8
7
10
9
DISASSEMBLY
1. Holding the lever or knob handle (2 or 4) with one hand, unscrew the handle hub
(9) counter-clockwise as shown above and set aside.
2. Using cartridge removal tool (not supplied), unscrew the cartridge nut counterclockwise.
3. Grasp the cartridge stem with pliers as shown above and pull straight up.
4. To reassemble, reverse the previous steps. Turn the cartridge stem to ON position
so that the hole in the piston lines up with the hole in the outer shell. Push the
cartridge straight down into the body, making sure the key on the cartridge fits into
the notch in the body. This will correctly position the cartridge. Replace the
cartridge nut, start by hand, DO NOT CROSS THREAD, and tighten firmly.
5. To replace the handle assemblies, see handle installation instructions on page 2.

CONSUMER INFORMATION

Faucets made of leaded brass alloys may contribute small amounts of lead to water that is allowed to stand in contact with the brass. The amount of lead contributed by any faucet
is highest when the faucet is new. The following steps may reduce potential exposure to lead from faucets and other parts of the plumbing system:
• Always run the water for a few seconds prior to use for drinking or cooking
• Use only cold water for drinking or cooking
• If you wish to flush the entire plumbing system of water that has been standing in the pipes or other fittings, run the cold water until the temperature of the water drops, indicating
water coming from the outside main
• If you are concerned about lead in your water, have your water tested by a certified laboratory in your area
FLUSHING INSTRUCTIONS
IMPORTANT: Pipe chips, sand, stones and other solids found in new and renovated plumbing can damage the sealing surfaces of the cartridge and cause leaks. To avoid damage,
DO NOT TURN ON SUPPLY VALVES until instructed below:
1. After installing and connecting your new faucet, make sure that the handles are in the on or open position (rotate hot handle counterclockwise and cold handle clockwise).
2. Open hot and cold water shut off valves and allow the water to run for 15 seconds.
3. Turn both handles to the off or closed position (rotate hot handle clockwise and cold handle counterclockwise).
4. Unscrew aerator from the end of spout and clean the cone screen.
5. Replace the aerator and check system for leaks.
MOEN LIFETIME LIMITED WARRANTY
Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the
"Warranty Period" for homeowners), that this faucet will be leak and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship. All other purchasers
(including purchasers for industrial, commercial and business use) are warranted for a period of 5 years from the original date of purchase (the "Warranty Period" for non-homeowners).
If this faucet should ever develop a leak or drip during the Warranty Period, Moen will FREE OF CHARGE provide the parts necessary to put the faucet back in good working condition and will replace FREE OF CHARGE, any
part or finish that proves defective in material and manufacturing workmanship, under normal installation, use and service. Replacement parts may be obtained by calling 1-800-289-6636 (Canada 1-800-465-6130), or by writing
to the address shown. Proof of purchase (original sales receipt) from the original consumer purchaser must accompany all warranty claims. Defects or damage caused by the use of other than genuine Moen parts are not covered
by this warranty. This warranty is applicable only to faucets purchased after December 1995 and shall be effective from the date of purchase as shown on purchaser's receipt.
This warranty is extensive in that it covers replacement of all defective parts and finishes. However, damage due to installation error, product abuse, product misuse, or use of cleaners containing abrasives, alcohol or other
organic solvents, whether performed by a contractor, service company, or yourself, are excluded from this warranty. Moen will not be responsible for labor charges and/or damage incurred in installation, repair or replacement, nor
for any indirect, incidental or consequential damages, losses, injury or costs of any nature relating to this faucet. Except as provided by law, this warranty is in lieu of and excludes all other warranties, conditions and guarantees,
whether expressed or implied, statutory or otherwise, including without restriction those of merchantability or of fitness for use.
Some states, provinces and nations do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state, province to province, nation to nation. Moen will advise you of the procedure to follow in making warranty claims. Simply write to Moen Incorporated using the address
below. Explain the defect and include proof of purchase and your name, address, area code and telephone number.
Helpline
Call our toll free helpline number:
1 (800) 289-6 6 3 6
1 (800) BUY-MOEN
For answers to any product, installation
replacement parts, or warranty questions.
Hours of operation are:
8:00 A.M. - 8 P.M. EST. Monday - Friday
8: A.M. - 6:30 P.M. EST. Saturday
3
1 DrainPlug Head Piece
2 DrainPlug O-Ring
3 SeatCover
(not included in Chrome Models)
4 DrainPlug Base
5 Lift Rod & Knob
6 Seat
7 Lift Rod Strap
8 Lift od Strap Screw
9 Spring Clip
10 Pivot Rod
7:30 A.M. - 5:00 P.M. EST. Monday - Friday
7:30 A.M. - 5:00 P.M. EST. Monday - Friday
Visit our website at www.moen.com for more information
Correct Disassembly
Lavatory Waste
Instructions:
1. Place the Seat Cover (3) into seat (6)
and push down carefully. Be careful
not to bend the Seat Cover.
2. Screw the Drain Plug Head piece (1)
firmly onto the Drain Plug Base (4). Be
careful not to cross thread the parts.
Ensure that the o-ring is correctly
seated on the Drain Plug Head Piece.
3. Connect the Pivot Rod (10) to the lift
rod strap (7) using the spring clip (9).
4. Place the drain plug into the full open
1
In Canada:
1-800-465-6130
Hours of operation are :
Toronto:
1-905-829-3400
Hours of operation are :
Incorrect Disassembly
Trim Installation position, loosen the lift rod strap screw
(8) and adjust the lift rod (5) height so
that the knob clears the faucet spout.
Tighten the lift rod strap screw.
Installation is now complete.
To disassemble the waste assembly,
reverse the steps as listed above.
order to remove seat cover, use a
screwdriver to bend snap features back
from the inside as shown above. Do not
try to lift the seat cover with any tool from
the outside.
2 3
In Mexico:
(84) 88-08-26, 88-08-27,
o 91-800-84345
Hours of operation are :
8:00 A.M. - 8 P.M. EST. Monday - Friday
8: A.M. - 6:30 P.M. EST. Saturday
In
4
STEM
KEY
CARTRIDGE
HOLE IN
SHELL
PISTON
INS329A