Explanation Of Symbols; Declaration Of Ec Conformity; General Safety Instructions - Silverline 868861 Manual Del Usuario

Explanation of symbols

• Do not dispose of WEEE (Waste Electrical
and Electronic Equipment) as unsorted waste.
• Class II construction (Double insulated).
• Wear gloves
• Wear breathing protection
• Wear eye protection
• Wear hearing protection
Specification
Drill:
Voltage: 12V
No load speed: 0-400/0-1200RPM
Drilling capacities:
Mild steel: 10mm
Wood: 25mm
Weight: 2.5kg
Weighted vibration: 7.87m/s
Sound pressure: 71.6dB(A)
Sound power: 86dB(A)
Battery:
Voltage: 12V
Capacity: 1.7Ah
Type: Ni-Cd
Charger:
Voltage: 230V
Frequency: 50Hz
Fuse rating: 5A
Double insulated:
Silverline Tools reserves the right to alter product
specifications without notice.

Declaration of EC conformity

Product number: 868861
12V Drill Driver
Description:
Silverline Tools Ltd declares that the above product conforms
to the following directive(s):
98/37/EC, 89/336/EEC
With reference to:
EN 60745-2-1:2003
EN 60745-2-2:2003
EN 60745-1:2003+A1:2003
EN 55014-1:2000/+A1:2001
EN 55014-2:1997/+A1:2001
EN 61000-3-2:2000
EN 61000-3-3:1995/+A1:2001
Peter Speller
Director
Silverline Tools Ltd
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, UK
3
868861_Instructions.indd 5
2

General safety instructions

Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual
risk factors. Use with caution. If you are at all unsure of the correct and
safe manner in which to use this tool, do not attempt to use it.
Remove adjusting keys
• Always check to see that keys and adjusting devices are removed from
the tool before use.
Clean the work area
• Accidents can occur where benches and work areas are cluttered
or dirty, floors must be kept clear, avoid working where the floor is
slippery. If working outdoors, make yourself aware of all potential
slip and trip hazards before using this tool.
Children and pets
• Children and pets should always be kept at a safe distance from your
work area. Lock tools away where children can't get access to them.
Do not allow children, or untrained persons to use this tool.
Use the correct tool
• Don't force, or attempt to use a tool for a purpose it was not
designed for.
Wear suitable clothing and footwear
• Don't wear loose fitting clothing, neckties, jewellery, or other items
which may become caught. Wear non slip footwear or footwear with
protective toe caps where appropriate. Long hair should be covered
or tied back.
Keep your balance
• Don't over reach, keep proper footing at all times, do not use tools
when standing on an unstable surface.
Accessories
• The use of any attachment or accessory other than those mentioned in
this manual could result in damage or injury. The use of improper
accessories could be dangerous, and will invalidate your guarantee.
Secure work
• Always ensure work is secure. If appropriate use a clamp or vice.
Check for damaged or missing parts
• Before each use, check if any part of the tool is damaged or missing,
check carefully that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or
other part that is damaged should be immediately repaired or replaced
by an authorised service centre. Do not use if defective.
20/10/2011 14:24