Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
DW871/384765-01-00
2/10/00
Minimum Gage for Cord Sets
Volts
120V
0-25
26-50
240V
0-50
51-100 101-200
Ampere Rating
More
Not more
Than
Than
0
-
6
18
6
-
10
18
10 -
12
16
12 -
16
14
• WEAR PROPER APPAREL. Do not wear loose clothing, neckties,
rings, bracelets, or other jewelry which may get caught in moving
parts. Nonslip footwear is recommended. Wear protective hair
covering to contain long hair.
•
ALWAYS USE SAFETY GLASSES. Also use face or dust mask if
cutting operation is dusty. Everyday eyeglasses only have impact
resistant lenses, they are NOT safety glasses.
•
SECURE WORK. Use clamps or a vise to hold work when practical.
It's safer than using your hand and it frees both hands to operate tool.
•
DON'T OVERREACH. Keep proper footing and balance at all times.
•
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best
and safest performance. Follow instructions for lubricating and
changing accessories.
•
DISCONNECT TOOLS before servicing; when changing accessories,
such as blades, bits, cutters, and the like.
•
REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure
switch is in off position before plugging in.
•
USE RECOMMENDED ACCESSORIES. Consult the instruction
manual for recommended accessories. The use of improper
accessories may cause risk of injury to persons.
•
NEVER STAND ON TOOL. Serious injury could occur if the tool is
tipped or if the cutting tool is unintentionally contacted.
•
CHECK DAMAGED PARTS. Before further use of the tool, a guard or
other part that is damaged should be carefully checked to determine
that it will operate properly and perform its intended function — check
for alignment of moving parts, binding of moving parts, breakage of
10:07 AM
Page 5
Total Length of Cord in Feet
51-100
101-150
201-300
American Wire Gage
16
16
14
16
14
12
16
14
12
12
Not Recommended
parts, mounting, and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or
replaced.
•
DIRECTION OF FEED. Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only.
•
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER
OFF. Don't leave tool until it comes to a complete stop.
•
REPLACEMENT PARTS. When servicing use only identical
replacement parts.
•
TO REDUCE THE RISK OF ELECTRIC SHOCK, this equipment has a
polarized plug (one blade is wider than the other.) This plug will fit in a
polarized outlet only one way. If the plug does not fit, contact a qualified
electrician to install the proper outlet. DO NOT CHANGE THE PLUG IN
ANY WAY.
Additional Safety Rules for Chop Saw
•
Always wear safety goggles or other eye protection when using this tool.
•
Before using, inspect each cutting wheel for cracks or flaws. If a crack
or flaw is evident—discard the wheel! The wheel should also be
inspected whenever you think the tool may have been dropped.
•
When starting the tool (with a new or replacement wheel installed)
place the tool in a well protected area. If the wheel has an undetected
crack or flaw, it should burst in less than one minute. Never start the
tool with a person in line with the wheel. This includes the operator.
•
In operation, avoid bouncing the wheel or giving it rough treatment.
If this occurs, stop the tool and inspect the wheel.
•
Clean your chop saw periodically following the procedure in this manual.
•
Do not remove wheel guard.
•
Always use the vise or special fixturing to clamp work.
•
Use only 14" type 1 wheels rated at 4100 rpm or higher.
•
Allow cut off parts to cool before handling.
•
Do not attempt to cut wood or plastic with this tool.
•
NEVER CUT MAGNESIUM WITH THIS TOOL.
•
Use chop saw in a well-ventilated area.
•
Turn chop saw off before removing any pieces from the base.
• DO NOT CUT ELECTRICALLY LIVE MATERIAL.
2
Publicidad
Tabla de contenido
