Riester ri-magic Instrucciones Para El Uso página 10

out under the increased influence of detrimental field strengths, i.e. when operating
mobile telephones and radiological equipment.
Attention!
• Don't use the examination light for eye-examination.
• There may be a risk of gas ignition when the light is used in the presence of in-
flammable drug mixtures such as air and/or oxygen or laughing gas!
• The light should only be opened by skilled persons to avoid a risk of lethal elec-
trocution.
• Please use exclusively the included plug connector.
Manufacturer Glob Tek Type GTM96180-1507-2.0
4. Assembly instructions prior to start-up
a) ri-magic
HPLED
®
Attach universal clamp (1) and screw set (2) to a desk or wall rail. Insert universal
light (4) from top into the bore of the screw clamp and fix with the knurled bolt (5).
Connect cable plug (6) of the power pack (7) to the socket (8) from below until enga-
ging with a click. Connect a transformer (7) to the socket. The light is now ready for
operation.
b)
ri-magic HPLED
®
Hold wall bracket (1a) to the desired point on the wall and mark 4 holes for dowels.
Remove wall bracket and drill the 4 marked holes. Insert dowels into the wall. Apply
wall bracket and fix with screws. Insert light (4) into bracket from above and fix by the
locking screw (3a) on the side. Connect cable plug (6a) of power pack (7a) to socket
(8a) from below until it engages with a click. Connect transformer (7a) to the socket.
The light is now ready for operation.
Attention:
The wall must absolutely be solid enough for a good and guaranteed fixation of the
diagnostic lamp. Please only use the included screws and anchors. Possibility of
alternative use of 6 mm anchors with lens head screw DIN 95 3 x 40 mm.
Installation instructions:
Please pay attention to the enclosed assembly instructions of the mounting systems
when installing the accessories.
In order to ensure an all-pole disconnection from the power supply at all
times, the ME device must be installed in such a way that the power cable is
accessible and can be disconnected.
c) ri-magic
HPLED
®
Assembly:
Please assemble the mobile stand first and thereby take note of the installation in-
struction
attached. Connect cable plug (6b) of power pack (7b) to the socket (8b) on the side
until an audible click is heard. The light is now ready for operation.
To be able to move properly, the flexible arm (head) must be bent down-
wards, so that the light is not too high and does not hit nearby objects and so
that there is no excess weight when the lamp is slightly inclined.
5. Start-up and operation Initially
Connect the cable plug (6,a,b) to the socket (8,a,b). Connect power pack (7,a,b) to the
mains sokket. Voltages on the rating plate of the mains adapter must be noted at all
times. There are two optional voltages: 230 V and 120 V.
On-Off
Turn the rheostat (9) in clockwise direction. When a click is heard, the light is swit-
ched on. Turn the rheostat (9) in counter-clockwise direction until a click is heard.
The light is now switched off. The Diagnostic lamp can also be interrupted from the
main power supply by removing the plug connector out of the socket.
Rheostat
The desired light intensity may be set by turning the rheostat (9). Increase light inten-
sity by turning in clockwise direction and decrease by turning in counter-clockwise
direction. Focusing A focusing ring (10) is provided at the front of the light head for
controlling the light cone of the light.
Focusing
There is a focusing ring (10) on the front of the lamphead. This ring can be used to
regulate the light cone of the lamp.
Note:
• The flexible arm of the light should not be bent in a too small radius in order to
prevent premature material fatigue.
10
desk model
wall model
stand model