Layout And Items Supplied - EINHELL TC-HP 1538 PC Kit Manual De Instrucciones

dosing instructions of the manufacturer.
•
The high-pressure jet can damage vehicle
tires and tire parts. Keep a distance of at least
30 cm from the object being cleaned.
•
If there is a power failure while you are using
the machine, be sure to switch off the machi-
ne for safety reasons.
•
The electric pump always must be able to
draw on a sufficient supply of water. Dry ope-
ration causes severe damage to the seals.
Special safety information
•
Danger of explosion – Do not spray flamma-
ble liquids.
•
Water that has passed through the non-return
valve is not drinkable.
•
During cleaning or maintenance or when
replacing parts or converting the machine to
a different function, pull the plug out of the
socket.
•
CAUTION! Unsuitable extension cables can
be dangerous. If an extension cable is used,
it must be suitable for outdoor use. The power
connection must be kept dry and must not
come into contact with the ground. We there-
fore recommend using a cable drum where
the power socket is kept at least 60 mm abo-
ve the ground.
•
Make sure that no exhaust gas emissions oc-
cur near the air inlets.
•
If pipe cleaning hoses are used, the hose
must be inserted at least one meter into the
pipe to prevent the hose from whipping out of
control.
•
CAUTION! If you leave this equipment un-
supervised even for a short length of time,
switch it off and take the plug out of the so-
cket.
•
This equipment must not be used by children.
Children must always be supervised to ensu-
re that they do not play with this equipment.
•
This equipment can be used by children of
8 years and older and by people with limited
physical, sensory or mental capacities or tho-
se with no experience and knowledge if they
are supervised or have received instruction
in how to use the equipment safely and un-
derstand the dangers which result from such
use. Children are not allowed to play with the
equipment. Unless supervised, children are
not allowed to clean the equipment or carry
out user-level maintenance work.
•
If the power cable for this equipment is dama-
ged, it must be replaced by the manufacturer
Anl_SA_TC_HP_1538_PC _SPK8.indb 16 Anl_SA_TC_HP_1538_PC _SPK8.indb 16
GB
or OEM after-sales service or by similarly
trained personnel to prevent hazards.
•
CAUTION: To prevent hazards arising from
the unintentional resetting of the thermal cut-
out, never connect the equipment to an exter-
nal switching device such as a timer switch
or to an electric circuit which is regularly swit-
ched on and off by a device.

2. Layout and items supplied

2.1 Layout (Fig. 1-2)
1. Handle
2. Accessory mount
3. On/Off switch
4. Water inlet connector
5. Pressure cleaner
6. Power cable
7. Connector for high-pressure hose
8. Gun
9. Extension
10. Cleaning agent container
11. Setting wheel
12. Quick connection system
13. Rotating nozzle
14. Point / wide jet nozzle
15. High-pressure hose
16. Terrace cleaner
17. Rotor
A. Nozzle cleaning pin
2.2 Items supplied
Please check that the article is complete as spe-
cifi ed in the scope of delivery. If parts are missing,
please contact our service center or the nearest
branch of the DIY store where you made your
purchase at the latest within 5 work days after
purchasing the article and upon presentation of
a valid bill of purchase. Also, refer to the warranty
table in the warranty provisions at the end of the
operating instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
- 16 -
25.04.16 08:47 25.04.16 08:47