Layout And Items Supplied - EINHELL TC-HP 90 Manual De Instrucciones Original

table protection gear.
•
Use cleaning agents sparingly. Observe the
dosing instructions of the manufacturer.
•
The high-pressure jet can damage vehicle
tires and tire parts. Keep a distance of at least
30 cm from the object being cleaned.
•
If there is a power failure while you are using
the machine, be sure to switch off the machi-
ne for safety reasons.
•
The electric pump always must be able to
draw on a sufficient supply of water. Dry ope-
ration causes severe damage to the seals.
Special safety information
•
Danger of explosion – Do not spray flamma-
ble liquids.
•
Water that has passed through the non-return
valve is not drinkable.
•
During cleaning or maintenance or when
replacing parts or converting the machine to
a different function, pull the plug out of the
socket.
•
CAUTION! Unsuitable extension cables can
be dangerous. If an extension cable is used,
it must be suitable for outdoor use. The power
connection must be kept dry and must not
come into contact with the ground. We there-
fore recommend using a cable drum where
the power socket is kept at least 60 mm abo-
ve the ground.
•
Warning! Make sure that no exhaust gas
emissions occur near the air inlets.
•
If pipe cleaning hoses are used, the hose
must be inserted at least one meter into the
pipe to prevent the hose from whipping out of
control.
•
CAUTION! If you leave this equipment un-
supervised even for a short length of time,
switch it off and take the plug out of the so-
cket.
•
This equipment must not be used by children.
Children must always be supervised to ensu-
re that they do not play with this equipment.
•
This machine is not allowed to be used by
persons (including children) with reduced
physical, sensory or mental capacities or tho-
se with a lack of experience and knowledge.
•
If the power cable for this equipment is dama-
ged, it must be replaced by the manufacturer
or OEM after-sales service or by similarly
trained personnel to prevent hazards.
•
CAUTION: To prevent hazards arising from
the unintentional resetting of the thermal cut-
out, never connect the equipment to an exter-
nal switching device such as a timer switch
Anl_SA_TC_HP_90_SPK8.indb 28 Anl_SA_TC_HP_90_SPK8.indb 28
GB
or to an electric circuit which is regularly swit-
ched on and off by a device.

2. Layout and items supplied

2.1 Layout (Fig. 1-3)
1. Handle
2. ON/OFF switch
3. Water inlet connector
4. Pressure cleaner
5. Gun
6. Extension
7. Solid cone/flat fan lance
8. High-pressure hose
9. Water inlet connector
10. Cable holder
11. Nozzle cleaning needle
12. Screw for fitting the handle
13. Connector for high-pressure hose
2.2 Items supplied
Please check that the article is complete as spe-
cified in the scope of delivery. If parts are missing,
please contact our service center or the nearest
branch of the DIY store where you made your
purchase at the latest within 5 work days after
purchasing the article and upon presentation of
a valid bill of purchase. Also, refer to the warranty
table in the warranty provisions at the end of the
operating instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suffocating!
•
High Pressure Cleaner
•
Water inlet connector
•
Gun
•
Extension
•
Solid cone/flat fan lance
•
Nozzle cleaning needle
- 28 -
05.10.2020 10:07:15 05.10.2020 10:07:15